Pioneering for You
en Installation and operation instructions with functional description
de Einbau- und Betriebsanleitung mit Funktionsbeschreibung
The language of the original operating instructions is German. All other languages of these instructions are translations of the original operating instructions.Die Sprache der Originalbetriebsanleitung ist Deutsch. Alle weiteren Sprachen dieser Anleitung sind eine Übersetzung der Originalbetriebsanleitung.
These installation and operating instructions are an integral part of the product. They must be kept readily available at the place where the product is installed. Strict adherence to these instructions is a precondition for the proper use and correct operation of the product.Die Einbau- und Betriebsanleitung ist Bestandteil des Produktes. Sie ist jederzeit in Produktnähe bereitzustellen. Das genaue Beachten dieser Anweisung ist Voraussetzung für den bestimmungsgemäßen Gebrauch und die richtige Bedienung des Produktes.
These installation and operating instructions correspond to the relevant version of the product and the underlying safety standards valid at the time of going to print.Die Einbau- und Betriebsanleitung entspricht der Ausführung des Gerätes und dem Stand der zugrunde gelegten sicherheitstechnischen Normen bei Drucklegung.
These operating instructions contain basic information which must be adhered to during installation and operation. For this reason, these operating instructions must, without fail, be read by the service technician and the responsible operator before installation and commissioning.Diese Betriebsanleitung enthält grundlegende Hinweise, die bei Aufstellung und Betrieb zu beachten sind. Daher ist diese Betriebsanleitung unbedingt vor Montage und Inbetriebnahme vom Monteur sowie dem zuständigen Betreiber zu lesen.
It is not only the general safety instructions listed under the main point “safety” that must be adhered to but also the special safety instructions with danger symbols included under the following main points.Es sind nicht nur die unter diesem Hauptpunkt Sicherheit aufgeführten allgemeinen Sicherheitshinweise zu beachten, sondern auch die unter den folgenden Hauptpunkten mit Gefahrensymbolen eingefügten, speziellen Sicherheitshinweise.
Symbols:Symbole:
General danger symbolAllgemeines Gefahrensymbol
Danger due to electrical voltageGefahr durch elektrische Spannung
NoteHinweis
Signal words:Signalwörter:
DANGER!GEFAHR!
Acutely dangerous situation. Non-observance results in death or the most serious of injuries.Akut gefährliche Situation. Nichtbeachtung führt zu Tod oder schwersten Verletzungen.
WARNING!WARNUNG!
The user can suffer (serious) injuries. ‘Warning’ implies that (serious) injury to persons is probable if this information is disregarded.Der Benutzer kann (schwere) Verletzungen erleiden. ‘Warnung’ beinhaltet, dass (schwere) Personenschäden wahrscheinlich sind, wenn der Hinweis missachtet wird.
CAUTION!VORSICHT!
There is a risk of damage to the product/unit. ‘Caution’ implies that damage to the product is likely if this information is disregarded.Es besteht die Gefahr, die Pumpe/Anlage zu beschädigen. ‘Vorsicht’ bezieht sich auf mögliche Produktschäden durch Missachten des Hinweises.
NOTE: Useful information on handling the product. It draws attention to possible problems.HINWEIS: Ein nützlicher Hinweis zur Handhabung des Produktes. Er macht auch auf mögliche Schwierigkeiten aufmerksam.
The installation, maintenance and repair personnel must have the necessary qualifications for this work.Das Personal für die Montage muss die entsprechende Qualifikation für diese Arbeiten aufweisen.
Non-observance of the safety instructions can result in risk of injury to persons and damage to product/unit. Non-observance of the safety instructions will result in the loss of any claims to damages.Die Nichtbeachtung der Sicherheitshinweise kann eine Gefährdung für Personen und das Produkt/die Anlage zur Folge haben. Die Nichtbeachtung der Sicherheitshinweise führt zum Verlust jeglicher Schadenersatzansprüche.
In detail, non-observance can, for example, result in the following risks:Im Einzelnen kann Nichtbeachtung beispielsweise folgende Gefährdungen nach sich ziehen:
The existing directives for accident prevention must be adhered to. Danger from electrical current must be eliminated. Local directives or general directives [e.g. IEC, VDE etc.] and those of local power supply companies must be adhered to.Die bestehenden Vorschriften zur Unfallverhütung sind zu beachten. Gefährdungen durch elektrische Energie sind auszuschließen. Weisungen lokaler oder genereller Vorschriften [z. B. IEC, VDE usw.] und der örtlichen Energieversorgungsunternehmen sind zu beachten.
This device may be used by children with an age of 8 years or above as well as by persons with reduced corporal, sensorial or mental capacity or lack of experience and/or lack of knowledge, if they are supervised or instructed regarding the safe operation of the device and understand the resulting dangers. Children shall not play with the device. Cleaning or user maintenance shall not be performed by children without supervision.Dieses Gerät kann von Kindern ab 8 Jahren und darüber sowie von Personen mit verringerten physischen, sensorischen oder mentalen Fähigkeiten oder Mangel an Erfahrung und Wissen genutzt werden,wenn sie beaufsichtigt oder bezüglich des sicheren Gebrauchs des Geräts unterwiesen wurden und sie die daraus resultierenden Gefahren verstehen. Kinder dürfen nicht mit dem Gerät spielen. Reinigung und Benutzerwartung dürfen nicht von Kindern ohne Beaufsichtigung durchgeführt werden.
The operator must ensure that all inspection and installation work is carried out by authorized and qualified personnel, who are sufficiently informed from their own detailed study of the operating instructions.Der Betreiber hat dafür zu sorgen, dass alle Inspektions- und Montagearbeiten von autorisiertem und qualifiziertem Fachpersonal ausgeführt werden, das sich durch eingehendes Studium der Betriebsanleitung ausreichend informiert hat.
Work on the product/unit should only be carried out when it has been brought to a standstill. It is mandatory that the procedure described in the installation and operating instructions for shutting down the product/unit be complied with.Die Arbeiten an dem Produkt/an der Anlage dürfen nur im Stillstand durchgeführt werden. Die in der Einbau- und Betriebsanleitung beschriebene Vorgehensweise zum Stillsetzen des Produktes/der Anlage muss unbedingt eingehalten werden.
Modifications to the product are only permissible after consultation with the manufacturer. Original spare parts and accessories authorized by the manufacturer ensure safety. The use of other parts can nullify the liability from the results of their usage.Veränderungen des Produktes sind nur nach Absprache mit dem Hersteller zulässig. Originalersatzteile und vom Hersteller autorisiertes Zubehör dienen der Sicherheit. Die Verwendung anderer Teile kann die Haftung für die daraus entstehenden Folgen aufheben.
The operating reliability of the supplied product is only guaranteed if the product/unit is used as intended in accordance with Section 4 of the operating instructions. The limit values must on no account fall under or exceed those specified in the catalogue/data sheet.Die Betriebssicherheit des gelieferten Produktes ist nur bei bestimmungsgemäßer Verwendung entsprechend Abschnitt 4 der Betriebsanleitung gewährleistet. Die im Katalog/Datenblatt angegebenen Grenzwerte dürfen auf keinen Fall unter- bzw. überschritten werden.
Immediately check for any transit damage and/or completeness on arrival. Complain immediately if necessary.Nach Lieferung unverzüglich auf Schäden und Vollständigkeit prüfen. Gegebenenfalls sofort reklamieren.
CAUTION! Danger of damage to the CIF-Module! Danger of damage due to incorrect handling during transportation and storage. VORSICHT! Beschädigungsgefahr für das CIF-Modul! Gefahr der Beschädigung durch unsachgemäße Handhabung bei Transport und Lagerung.
The unit must be protected from moisture, frost and mechanical damage during transport and interim storage.Das Gerät ist bei Transport und Zwischenlagerung gegen Feuchtigkeit, Frost und mechanische Beschädigung zu schützen.
The CIF-Modules are designed for external control and operating status signalling of Wilo pumps. The CIF-Modules are not designed for safe deactivation of the pump.Die CIF-Module sind geeignet zur externen Steuerung und Meldung von Betriebszuständen von Wilo-Pumpen. Die CIF-Module sind nicht geeignet zur sicherheitsgerichteten Abschaltung der Pumpe.
DANGER! Risk of injury and material damage!GEFAHR! Gefahr von Personen- und Sachschäden!
Never use the control inputs for safety functions.Niemals die Steuereingänge für Sicherheitsfunktionen verwenden.
Never mount the CIF-Module in a non-compatible device.Niemals das CIF-Modul in nicht kompatible Geräte einbauen.
This document is valid for a firmware version of up to 5.00 of the CIF-module.Dieses Dokument ist gültig für eine Firmware-Version bis 5.00 des CIF-Moduls.
To ensure the functionality of the module the following (or higher) firmware versions for the product where the CIF-module is mounted are necessary:Um die Funktion des CIF-Moduls zu gewährleisten, sind die folgenden Firmware-Versionen (oder höher) des Produkts notwendig, in welches das Modul eingebaut wird:
Note:Hinweis:
Firmware version (SW) is on a sticker close to mains terminal.Die Firmwareversion (SW) findet sich auf einem Aufkleber unter dem Klemmenkastendeckel.
Firmware version (SW) can be read out at <4.4.2.0>.Die Firmwareversion (SW) ist über das Menü <4.4.2.0> abrufbar.
Firmware version (SW) can be read out at Monitoring / Device Information / Software Version.Die Firmwareversion (SW) ist über das Menü Monitoring / Geräteinformationen / Software Version abrufbar.
Firmware can be updated with the app "Wilo-Assistant".Die Firmware kann mit der App "Wilo-Assistent" aktualisiert werden.
PumpPumpe | Pump SW VersionSoftware Version Pumpe | RemarkBemerkung | |||
---|---|---|---|---|---|
WILO Stratos Maxo | 01002500 | CIF Modbus RTU, BACnet MS/TP, LON, PLR | |||
WILO Stratos Maxo | 0103201 | CIF CANopen | |||
WILO Stratos Maxo | 01042500 | CIF Ethernet Multiprotocol (Modbus TCP, BACnet/IP) | |||
WILO Stratos Maxo | 01002500 | CIF module version 1.00 | CIF module version 4.00 | ||
WILO Stratos Maxo | 01032101 | CIF module version 3.00 | CIF module version 1.00 | CIF module version 4.00 | |
WILO Stratos Maxo | 01040000 | CIF module version 3.02 | CIF module version 1.00 | CIF module version 4.00 | |
WILO Stratos Maxo | 01042500 | CIF module BACnet MS/TP version 3.02 / CIF module Ethernet Multiprotocol (BACnet/IP) version 3.03 | CIF module Modbus RTU version 3.02 / CIF module Ethernet Multiprotocol (Modbus TCP) version 3.03 | CIF module version 1.00 | CIF module version 4.00 |
WILO Stratos GIGA 2.0 | 01000300 | CIF module BACnet MS/TP version 5.00 / CIF module Ethernet Multiprotocol (BACnet/IP) version 5.00 | CIF module Modbus RTU version 5.00 / CIF module Ethernet Multiprotocol (Modbus TCP) version 5.00 | CIF module version 2.00 | CIF module version 4.00 |
WILO Stratos | 1.005.005.09 | ||||
WILO TOP-E | 1.004.00not compatiblenicht kompatibel | ||||
WILO Stratos GIGA | 1.00 | ||||
WILO Stratos GIGA B | 1.00 | ||||
WILO BL-E | 1.00 | ||||
WILO IP-E/DP-E | 2.003.00 | LC Display | |||
WILO IL-E/DL-E | 1.294.00 | LC Matrix Display | |||
WILO IL-E/DL-E | 3.02not compatiblenicht kompatibel | LC Segment Display | |||
WILO Helix EXCEL | 1.00 | ||||
WILO MVIE/MVISE/MHIE/HELIX VE (0.55…4 kW) | 2.003.00 | LC Display | |||
WILO MVIE/MVISE/MHIE/HELIX VE (5.5…7.5 kW) | 1.294.00 | LC Display | |||
WILO MVIE/MVISE/MHIE/HELIX VE (11…22 kW) | 1.001.00 | LC Display |
Für die Kompatibilität mit nicht oben aufgelisteten Produkten siehe www.wilo.de/automation
For compatibility with products not listed above, refer to www.wilo.com/automation
Pumps IL-E…BF cannot be used together with IF-Modules.Pumpen der Typenreihe IL-E…BF können nicht mit IF-Modulen betrieben werden.
This document does not apply for the DigiCon-LBF (2083942).Dieses Dokument gilt nicht für DigiCon-LBF (2083942).
For pumps of the series Stratos GIGA, Stratos GIGA B, BL-E, IP-E/DP-E or IL-E/DL-E functionality may vary.Für Pumpen der Baureihen Stratos GIGA, Stratos GIGA B, BL-E, IP-E/DP-E und IL-E/DL-E kann die Funktionalität abweichen.
If the menu item <5.7.2.0> "pressure correction" is not available on the pump display, the following functions are not available:Sollte bei einer Pumpe das Menü <5.7.2.0> „Druckwertkorrektur“ über das Display nicht zur Verfügung stehen, handelt es sich um eine Variante der Pumpe in der folgende Funktionen nicht zur Verfügung stehen:
Example: CIF-Module Modbus RTUBeispiel: CIF-Modul Modbus RTU
Example: IF-Module ModbusBeispiel: IF-Modul Modbus
Example: IF-Module Modbus StratosBeispiel: IF-Modul Modbus Stratos
KeyBezeichnung | DescriptionBeschreibung |
---|---|
CIF-ModuleCIF-ModulIF-ModuleIF-Modul | Communication Interface ModuleCommunication Interface ModulInterface ModuleInterface Modul |
Modbus |
Model/function identifier:Modell/Funktionsbezeichnung: Modbus RTU = RS485 interface, Modbus RTU protocolModbus RTU = Schnittstelle RS485, Protokoll Modbus RTU BACnet MS/TP = RS485 interface, BACnet MS/TP protocolBACnet MS/TP = Schnittstelle RS485, Protokoll BACnet MS/TP |
Stratos | suitable for this pump seriesGeeignet für diese Baureihe |
Fig. 5.1.1: type keyAbb. 5.1.1: Typenschlüssel
Technical SpecificationTechnische Daten | |
---|---|
General dataAllgemeine Daten | |
Terminal cross-section (finely stranded, no ferrules)Klemmquerschnitt (feindrähtig ohne Endhülsen) | 1.5 mm² (max) |
Electric circuitStromkreis | SELV, galvanically isolatedSELV, galvanisch getrennt |
mechanical mating cyclesSteckzyklen mechanisch | 250 |
Safety according EN 60335Sicherheit nach EN 60335 | mains voltage <=230 V TN/TT systemNetzspannung bis 230 V, TN/TT System |
Interface Ethernet in accordance with IEEE 802.3Schnittstelle Ethernet nach IEEE 802.3 | |
interfacesSchnittstellen | 2 (integrated switch)2 (integrierter Switch) |
Interface typeInterfacetyp | Auto MDI-X |
link typesVerbindungstyp | 10BASE-T, 100BASE-TX (half/full duplex, autonegotiation) |
connection typeAnschlusstyp | RJ45 jack (screeened)RJ45 Buchse (geschirmt) |
Cable lengthLeitungslänge | 100 m (max) |
Interface CAN in accordance with ISO 11898-2Schnittstelle CAN nach ISO 11898-2 | |
Cable lengthLeitungslänge | 200 m (max) |
Termination resistorAbschlusswiderstand | 120 Ω (integrated, switchable, default: off)120 Ω (integriert, schaltbar, Lieferzustand: aus) |
Contact Input (Ext. Off/Min)Kontakteingang (Ext. Off/Min) | |
typeAusführung | SELV, isolatedSELV, isoliert |
ground referenceBezugsmasse | shared with 0…10 V inputgemeinsam mit 0…10 V Eingang |
open loop voltageLeerlaufspannung | 10 V (max) |
loop currentSchleifenstrom | 10 mA (typical)10 mA (typisch) |
Contact Output SBMKontaktausgang SBM | |
typeAusführung | dry contact potentialfreier Kontakt |
ratingBelastbarkeit | 30 V AC/60 V DC: 1 A AC1/DC1 (SELV) |
min. loadMinimallast | 12 V DC / 10 mA |
Control input 0…10 VSteuereingang 0…10 V | |
typeAusführung | SELV, isolatedSELV, isoliert |
ground referenceBezugsmasse | shared with contact inputgemeinsam mit Kontakteingang |
Voltage rangeSpannungsbereich | 0…10 V |
Input resistanceEingangswiderstand | > 100 kΩ |
Precision (full range)Genauigkeit (absolut) | 5% |
Absolute maximum input voltageSpannungsfestigkeit | 24 V DC |
Interface RS485 in accordance with TIA-485-ASchnittstelle RS485 nach TIA-485-A | |
Load (unit load)Last (Einheitlast) | 1/8 |
Input voltageEingangsspannung | Max. 12 V (differential A-B)Max. 12 V (differentiell A-B) |
Termination resistorAbschlusswiderstand | 120 Ω (integrated, switchable, default: off)120 Ω (integriert, schaltbar, Lieferzustand: aus) |
Interface type TP/FT-10Schnittstelle TP/FT-10 | |
cable typeLeitungstyp | J-Y(St) Y 1 x 2 x 0,8 mm / CAT 5 AWG 22 |
cable lengthLeitungslänge | 900 m with bus topology (terminated on both ends) with max. 3 m stub length900 m bei Bustopologie (mit Abschlusswiderstand) und max. 3 m langen Stichleitungen |
450 m with free topology, with max. 250 m between two inter-communicating nodes450 m bei freier Topologie, dabei max. 250 m zwischen 2 untereinander kommunizierenden Knoten | |
Interface PLRSchnittstelle PLR | |
Interface typeSchnittstelle | current loop (≅ 5 mA)Stromschleife (≅ 5 mA) |
Cable lengthLeitungslänge | 200 m (max / 0.5 mm²) |
Double pump interface (DP)Doppelpumpenschnittstelle (DP) | |
Interface typeSchnittstelle | Wilo specific, short circuit proof, polarity independentWilo-spezifisch, dauerkurzschlussfest, verdrehsicher |
VoltageSpannung | max. 10 Vppmax. 10 Vss |
FrequencyFrequenz | approx. 150 kHzca. 150 kHz |
Cable lengthLeitungslänge | max. 3 m |
Digital sensor inputDigitale Sensor-Schnittstelle | |
Interface typeSchnittstelle | 3.3 V digital, half duplex3,3 V digital, halb-duplex |
Cable lengthLeitungslänge | max. 3 m |
Wireless interfaceDrathlos-Schnittstelle | |
Interface typeSchnittstelle | Bluetooth® LE 4.0 |
profileProfil | GATT peripheral server |
Frequency bandFrequenzband | 2400.0…2483.5 MHz |
Maximum radiated transmission powerAbgestrahlte maximale Sendeleistung | <10 dBm (EIRP) |
Overview about ProgramIDs and neuron application versions (SW) of the CIF-Modules LON.Überblick über die ProgramIDs und Neuro-Applikations-Versionen (SW) der CIF-Module LON.
Version | ProgramId | RemarkBemerkung |
---|---|---|
1.1c | 90:00:00:00:00:03:04:01 | - |
1.2 | 9F:FF:CC:00:00:03:04:02 | - |
1.3 | 9F:FF:CC:81:20:43:04:03 | - |
2.01 | 9F:FF:CC:51:14:06:04:04 | - |
2.02 | 9F:FF:CC:51:14:06:04:06 | - |
3.00 | 9F:FF:CC:51:14:06:04:05 | - |
4.00 | 9F:FF:CC:51:14:06:04:07 | functionality same as 3.00, but program ID changed due to hardware modificationfunktional identisch zu 3.00, Program-ID wegen Hardwaremodifikation geändert |
The CIF-Modules with protocol BACnet comply to ISO 16485-5:2017. For details refer to the PICS statement.Die CIF-Module mit Protokoll BACnet entsprechen ISO 16484-5:2017. Details finden Sie im PICS Statement (englisch).
Date: 2019-01-22
Vendor Name: Wilo SE
Product Name: CIF-Module BACnet Stratos MS/TP
Product Model Number: 219036720978112097810
Application Software Version ≥: 1.012.00
Firmware Revision ≥: 4.102.26
BACnet Protocol Revision: 1.4
This product extends a Wilo device with a BACnet Interface as defined in this statement. It is mounted inside the device.
BACnet Smart Actuator (B-SA)
BACnet Smart Sensor (B-SS)
Data Sharing Read Property Execute (DS-RP-B)
Data Sharing Write Property Execute (DS-WP-B)
Device Management Dynamic Object Binding (DM-DOB-B)
Device Management Dynamic Device Binding (DM-DDB-B)
Device Management Device Communication Control (DM-DCC-B)
The product does not support segmentation.
Object type | Object Supported | Dynamically Creatable | Dynamically Deletable | Optional Properties Supported | Optionally Writable Properties |
---|---|---|---|---|---|
Analog Input | yes | no | no | device-type | |
Analog Output | yes | no | no | device-type | |
Binary Input | yes | no | no | device-type | |
Binary Output | yes | no | no | device-type | |
Multistate Input | yes | no | no | device-type | |
Multistate Output | yes | no | no | device-type | |
Device | yes | no | no | location, description | max-master |
MS/TP master (Clause 9), baud rate(s): 9600, 19200, 38400, 76800, 115200
MS/TP slave (Clause 9), baud rate(s): 9600, 19200, 38400, 76800, 115200
The device is configured as MS/TP slave if MAC address is set to 128 or higher, otherwise it is configured as MS/TP master.
Static device binding is not supported.
The product has no networking options.
ISO 10646 (UTF-8)
ISO 8859-1
Indicating support for multiple character sets does not imply that they can all be supported simultaneously.
This product does not support any gateway options.
Non-secure Device - is capable of operating without BACnet Network Security
- End of PICS statement for revision 4 -
Date: 2020-12-15
Vendor Name: Wilo SE
Product Name: CIF-Module Ethernet Multiprotocol
Product Model Number: 2211408
Application Software Version ≥: 3.03
Firmware Revision ≥: 1.00
BACnet Protocol Revision: 1.16
This product extends a Wilo device with a BACnet Interface as defined in this statement. It is mounted inside the device.
BACnet Application Specific Controller (B-ASC
Data Sharing Read Property Execute (DS-RP-B)
Data Sharing Read Property Execute (DS-RPM-B)
Data Sharing Write Property Execute (DS-WP-B)
Data Sharing Write Property Execute (DS-WPM-B)
Data Sharing Change of Value Execute (DS-COV-B)
Device Management Dynamic Object Binding (DM-DOB-B)
Device Management Dynamic Device Binding (DM-DDB-B)
Device Management Device Communication Control (DM-DCC-B)
⦻ Able to transmit segmented messages Window size 8
⦻ Able to receive segmented messages Window size 8
Object type | Object Supported | Dynamically Creatable | Dynamically Deletable | Optional Properties Supported | Optionally Writable Properties |
---|---|---|---|---|---|
Analog Input | yes | no | no | ||
Analog Output | yes | no | no | ||
Binary Input | yes | no | no | ||
Binary Output | yes | no | no | ||
Multistate Input | yes | no | no | ||
Multistate Output | yes | no | no | ||
Device | yes | no | no | location, description |
BACnet/IP, (Annex J)
Static device binding is not supported.
The product has no networking options.
ISO 10646 (UTF-8)
Indicating support for multiple character sets does not imply that they can all be supported simultaneously.
This product does not support any gateway options.
Non-secure Device - is capable of operating without BACnet Network Security
- End of PICS statement for revision 16 -
The CIF-Modules CANopen comply to the following Die CIF-Module CANopen entsprechen folgenden CAN in Automation standardsStandards
The CIF-Modules LON complies to the following Die CIF-Module LON entsprechen folgenden LonMark International standards: Standards:
In order to get correct decoding of data, make sure that you have the resource files version 13.04 or later installed (available at Für eine korrekte Dekodierung der Daten ist die Installation der Resource Files Version 13.04 oder höher erforderlich. (Verfügbar bei LonMark International
If problems decoding data remain, you may refer to the online Wenn die Probleme bestehen bleiben, hilft evtl. die Online Referenz LONMARK type definition.Typ-Definition.
The CIF-Modules with protocol Modbus RTU comply to MODBUS APPLICATION PROTOCOL SPECIFICATION V1.1 and Modbus Serial line protocol V 1.02 in transmission mode RTU available at Die CIF-Module Modbus RTU entsprechen der MODBUS APPLICATION PROTOCOL SPECIFICATION V1.1 und dem dem Modbus over Serial Line protocol V 1.02 im Module mit Modus RTU, verfügbar unter modbus.org .
The CIF-modules expand the device with communication capability for various standards.Die CIF-Module erweitern das Gerät mit Kommunikationsschnittstellen für diverse Standards.
Weitergehende Informationen finden Sie unter www.wilo.de/automation
Further information available at www.wilo.com/automation
The following description replaces the reference to the website and contains the detailed description of the objects. The EDE file is available for download at the URL given below.Die folgende Beschreibung ersetzt den Verweis auf die Webseite und enthält die detaillierte Beschreibung der BACnet-Objekte. Die EDE-Liste ist zum Download verfügbar unter der weiter unten angegebenen Adresse.
The IF-modules BACnet support MS/TP master functionality starting with firmware version (SW) 2.00. The firmware version can be found on the sticker on top of the module.Die IF-Module BACnet unterstützen die MS/TP Master-Funktionalität ab der Firmware Version (SW) 2.00 Die Firmware-Version ist auf dem Typenschild des Moduls aufgedruckt.
When writing NULL (no value) to all elements of the priority array, the BACnet standard defines that in this case the relinquish default shall be used as present value. Some of the commandable objects (i.e. outputs) need to have a floating default. with the BACnet 1.4 implementation, the relinquish default is static and the floating default is realized by a virtual write on priority 16.Wenn man NULL (kein Wert) in alle Element des Priority Array schreibt, schreibt der BACnet-Standard vor, dass dann der Relinquish Default als Present Value übernommen wird. Einige der Commandable Objects (Ausgänge) benötigen jedoch einen variablen Default-Wert. Dieses Verhalten wird in der BACnet 1.4 Implementierung durch einen virtuellen Schreibbefehl auf Priorität 16 realisiert.
The following description replaces the reference to the website and contains the detailed description of the objects. The .eds file is available for download at the URL given below.Die folgende Beschreibung ersetzt den Verweis auf die Webseite und enthält die detaillierte Beschreibung der BACnet-Objekte. Die .eds Datei ist zum Download verfügbar unter der weiter unten angegebenen Adresse.
This paragraph is intentionally empty.Dieser Abschnitt bleibt leer.
Two objects, the node object and pump object, are implemented in the IF-Module LON. The node object is used to control individual objects within the node; errors which occur in the individual objects are also indicated centrally here. Im IF-Modul LON sind 2 Objekte realisiert, das Knoten-Objekt und das Pumpen-Objekt. Das Knoten-Objekt dient zur Steuerung einzelner Objekte innerhalb des Knotens, hier werden auch zentral Fehler signalisiert, die in den einzelnen Objekten auftreten.
When registers are 32 Bits wide (including REAL), the the most significant part ist stored at the base address, the least significant part is stored at base address +1.Wenn Register 32 Bit-Werte (incl. REAL) enthalten, dann wird der höherwertige 16-Bit Teil im Register mit der Basisadresse gespeichert, der niederwertige 16-Bit Teil in der Basisadresse+1.
When registers are 64 Bits wide (including LREAL), the the most significant part ist stored at the base address, the least significant part is stored at base address +3.Wenn Register 64 Bit-Werte (incl. LREAL)enthalten, dann wird der höherwertigste 16-Bit Teil im Register mit der Basisadresse gespeichert, der niederwertigste 16-Bit Teil in der Basisadresse+3.
This paragraph is intentionally empty.Dieser Abschnitt bleibt leer.
NOTEHINWEIS
Beside the normal on/off control of the pump there are several methods to override this. The following list shows the priority of those commands. Lower numbers have higher priorityNeben der normalen Ein/Aus Steuerung der Pumpe gibt es mehrere Möglichkeiten, diese zu übersteuern. Die folgende Liste zeigt die Prioritäten, wobei eine niedrigere Nummer eine höhere Priorität bedeutet.
This paragraph is intentionally empty.Dieser Abschnitt bleibt leer.
For pumps from the Stratos series a simple fluid temperature dependent variation of the delivery head was available as control function. Via IF-module, IR-Monitor or even IR-Stick, adjustment of parameters Tmin / Tmax and p(Tmin) / p(Tmax) was possible.Für Pumpen der Baureihe Stratos gab es diese einfache Funktion zur temperaturabhängigen Sollwert-Vorgabe. Über das IF-Modul konnten die Parameter Tmin, Tmax bzw. p(Tmin), p(Tmax) über den Bus bzw. IR-Monitor oder IR-Stick gewählt werden.
Pumps with CIF-Modules support a full featured constant temperature control with a sensor mounted directly in the fluid. The datapoints for the legacy function are still existing but without any function.Pumpen mit CIF-Modul unterstützen statt dessen eine vollwertige Konstanttemperatur-Regelung mit Sensor direkt im Medium. Die Datenpunkte der bisherigen Funktion sind aus Kompatibilitätsgründen noch vorhanden, aber funktionslos.
For usage of this function, select the mode "T-const" from the basic control functions.Zur Verwendung wird im Pumpenmenü aus den Basisregelungsarten "T-const" ausgewählt.
As setpoint source "internal setpoint" has to be selected.Als Sollwert-Quelle wird "interner Sollwert" gewählt.
A simple approach for adjustment may be to select the mean value of former Tmin and Tmax values as setpoint for the temperature control. There is no general recommendation for the settings. Also WILO does not guarantee full compatibility between Δp-c = F(T) and T-const control.Ein einfacher Startpunkt für die Einstellung ist, den bisherigen Mittelwert aus Tmax und Tmin als Sollwert für die Temperaturregelung zu verwenden. Eine allgemeine Empfehlung für die Umrechnung der Werte kann nicht gegeben werden. Auch übernimmt WILO keine Gewähr für die vollständige Kompatibilität der Funktionen Δp-c = F(T) und T-const.
The CIF-module LON has a program memory which can be deleted and overwritten to allow subsequent software updates to be loaded into this memory via the LON bus.Das CIF-Modul LON besitzt einen lösch- und wiederbeschreibbaren Programmspeicher, sodass ein späteres Software-Update über den LON-Bus in diesen Speicher geladen werden kann.
When CIF-Modules LON with an older software version (prior to 3.00) are replaced by version 3.00 or higer , an application software downgrade is not possible due to hardware reasons. The module has a new program ID and a new link must be created within the project.Bei Austausch eines CIF-Moduls LON mit einer älteren Software-Version (vor 3.00) ist ein Software downgrade aus Hardwaregründen nicht möglich und somit ein Knotentausch nicht ausreichend. Das Modul hat eine neue Programm-ID und muss im Projekt neu verknüpft werden.
The usage of remote sensors is currently non functional with CIF-ModulesDie Verwendung von Remote-Sensorwerten ist bei CIF-Modulen derzeit nicht möglich.
In case of replacement the pressure or temperature control functionality has to be moved to the DDC controller and the pump should be used as an actuator in constant speed mode.Im Fall des Ersatzes einer Pumpe mit dieser Funktionalität muss der Druck- bzw. Temperaturregler in die Steuerung verschoben werden. Die Pumpe kann dann als Drehzahlsteller agieren.
If the IF-module receives a "wink" command via the LON bus, a corresponding command is sent to the pump also in this condition and the "Id" indication is displayed at the pump for 30 s.Erhält das IF-Modul über den LON-Bus ein "Wink"-Kommando, so wird ein entsprechendes Kommando zur Pumpe gesendet und an der Pumpe erscheint die "Id"-Anzeige für 30 s.
The "wink" function is not available for CIF-modules.Die "Wink"-Funktion ist für CIF-Module nicht verfügbar.
For CIF modules, the data of the master and slave pump are not available individually (even if defined on the interface for compatibility). Only data of the system is provided. To achieve maximum compatibility in existing applications, all datapoints with the scope "master" show values of the pump system while all datapoints with the scope "slave" deliver the error value (if applicable) or a static value. Nevertheless, the pump on signal of the slave is provided individually.Für CIF-Module gibt es keine individuellen Daten von Master oder Slave (auch wenn dies am Interface aus Kompatibilitätsgründen definiert sein sollte). Nur Daten des Pumpensystems werden übermittelt. Für maximale Kompatibilität in Bestandssystemen werden bei allen Datenpunkten, die sich auf den Master beziehen, die Werte des Systems übermillelt. Bei Daten die die sich auf den Slave beziehen, wird - soweit anwendbar - der Fehlerwert bzw. ein statischer Wert übermittelt. In jedem Fall wird die Meldung "Pump On" individuell übermittelt.
When a scale is mentioned in the following sections, this is always a presentation scale. Read values have to be multiplied by this factor to get the result for presentation.Wenn in den folgenden Abschitten eine Skalierung angegeben ist, dann handelt es sich um einen Präsentationsfaktor. Ein gelesener Wert muss mit diesem Faktor multipliziert werden, um den Anzeigewert zu erhalten.
The setpoint (duty point (rel.)) is defined as a percentage. To scale to absolute values, you may use one of the values speed max-pres value / max pressure dp-c / max pressure dp-v which represent 100 % for the specific control function. A more generic approach is available for software versions 3.00 or higher. Here we provide a duty point 100% value indication the absolute value corresponding 100 %, the physical unit of this 100 % value (duty point (rel.) units) and additionally the relative limits of the duty point (duty point (rel.) min.-output / duty point (rel.) max.-output). Details are shown below:Der Sollwert (duty point (rel.)) ist als Prozentwert definiert. Zur Skalierung auf absolute Werte können Sie einen der Werte speed max-pres value / max pressure dp-c / max pressure dp-v benutzen, welche den jeweiligen 100 % Wert für die jeweilge Regelungsfunktion darstellen. Eine von der Regelungsfunktion unabhängige Definition ist ab der Software-Version 3.00 verfügbar. Hier wird die 100 % Referenz als absoluter Wert, die dazugehörige physikalische Einheit (duty point (rel.) units) und die relativen Grenzen (duty point (rel.) min.-output / duty point (rel.) max.-output) zur Verfügung gestellt (siehe nachfolgende Übersicht).
Name | register typeRegister-Typ | addressAdresse | functionFunktion |
---|---|---|---|
duty point (rel.) | Holding_register | 1 | in |
duty point (rel.) | Input_register | 200 | active |
duty point (rel.) maximum-output | Input_register | 202 | active |
duty point (rel.) minimum-output | Input_register | 204 | active |
duty point (rel.) units | Input_register | 208 | active |
duty point (rel.) | Input_register | 400 | out |
nameName | Objekttypobject type | instanceInstanz | functionFunktion |
---|---|---|---|
Bus Setpoint in | analog-output | 0 | in |
duty point (rel.) max.-outp. active | analog-input | 32 | active |
duty point (rel.) min.-outp. active | analog-input | 31 | active |
duty point (rel.) active | analog-input | 34 | active |
duty point (rel.) units active | multistate-input | 33 | active |
System Effective Capacity out | analog-input | 0 | out |
data typeDatentyp | Bit | min | max | encodingKodierung | descriptionBeschreibung |
---|---|---|---|---|---|
BOOL | 1 | 0 | 1 | Boolesch (Bit) - kann FALSE oder TRUE sein | |
BOOL | 1 | 0 | 1 | boolean (bit) - can be true or false | |
BYTE | 8 | 0 | 255 | used for e.g. bitsets, no error value | |
BYTE | 8 | 0 | 255 | für allgemeine Anwendung, kein Fehlerwert definiert | |
DATE | 32 | Datum | |||
DATE | 32 | date | |||
DINT | 32 | -2147483648 | 2147483647 | Vorzeichenbehafteter ganzzahliger Wert | |
DINT | 32 | -2147483648 | 2147483647 | signed numeric value | |
DT | 32 | Eingangswert: dieser Wert wird in das Gerät geschrieben (z. B. Sollwert, Schaltbefehl, Parameter) | |||
DT | 32 | input value: this value is written to the device (e.g. setpoint, command or parameter) | |||
DWORD | 32 | 0 | 4294967295 | used for e.g. bitsets, no error value | |
DWORD | 32 | 0 | 4294967295 | für allgemeine Anwendung, kein Fehlerwert definiert | |
INT | 16 | -32768 | 32767 | Vorzeichenbehafteter ganzzahliger Wert | |
INT | 16 | -32768 | 32767 | signed numeric value | |
LINT | 64 | Vorzeichenbehafteter ganzzahliger Wert | |||
LINT | 64 | signed numeric value | |||
LREAL | 64 | Gleitpunktzahl nach IEEE754 | |||
LREAL | 64 | floating point value according IEEE754 | |||
LWORD | 64 | used for e.g. bitsets, no error value | |||
LWORD | 64 | für allgemeine Anwendung, kein Fehlerwert definiert | |||
REAL | 32 | -3.4028234663852886e38 | 3.4028234663852886e38 | Gleitpunktzahl nach IEEE754 | |
REAL | 32 | -3.4028234663852886e38 | 3.4028234663852886e38 | floating point value according IEEE754 | |
SINT | 8 | -128 | 127 | Vorzeichenbehafteter ganzzahliger Wert | |
SINT | 8 | -128 | 127 | signed numeric value | |
STRING | US-ASCII | Zeichenfolge unterschiedlicher Länge mit deklarierter Maximallänge | |||
STRING | US-ASCII | string with variable length up to declared maximum size | |||
TIME | 32 | Tageszeit bis 24 h (Auflösung 1 ms) | |||
TIME | 32 | time of day up to 24 hours (resolution 1 ms) | |||
TIME_OF_DAY | 32 | time of day | |||
TIME_OF_DAY | 32 | Zeit des Tages | |||
UDINT | 32 | 0 | 4294967295 | Vorzeichenloser ganzzahliger Wert | |
UDINT | 32 | 0 | 4294967295 | unsigned numeric value | |
UINT | 16 | 0 | 65535 | Vorzeichenloser ganzzahliger Wert | |
UINT | 16 | 0 | 65535 | unsigned numeric value | |
ULINT | 64 | used for e.g. bitsets, no error value | |||
ULINT | 64 | für allgemeine Anwendung, kein Fehlerwert definiert | |||
USINT | 8 | 0 | 255 | Vorzeichenloser ganzzahliger Wert | |
USINT | 8 | 0 | 255 | unsigned numeric value | |
WORD | 16 | 0 | 65535 | used for e.g. bitsets, no error value | |
WORD | 16 | 0 | 65535 | für allgemeine Anwendung, kein Fehlerwert definiert | |
WSTRING | UNICODE | Zeichenfolge unterschiedlicher Länge mit deklarierter Maximallänge | |||
WSTRING | UNICODE | string with variable length up to declared maximum size |
In the subsequent sections, the keyword "error value" appears in the functional description. If a read value is identical to the error value, it indicates that the reading is not available or invalid. Sometimes error values are also indicated for write values. In this case, writing the error value may invalidate the functionality of this datapoint.In den folgenden Abschnitten wird das Schlüsselwort "Fehlerwert" verwendet. Wenn ein gelesener Datenpunkt den Fehlerwert enthält, ist der Wert nicht verfügbar oder ungültig. Für Datenpunkte, die geschrieben werden, kann mit dem Fehlerwert die Funktion des Datenpunkts ggfs. ausgeschaltet werden.
In general, several parameters can be written to the pump not only from the specified setpoint source, but also from other sources like HMI or a remote control. The write access is typically possible in parallel to the write access from the CIF-module. Normally the last write wins, independent of the source. To realize that, values from the interface are forwarded to the pump on change. If you want to guarantee that a desired value is forced, you should first read the active value from the pump, write that back to the input and then write the value to be forced. With this principle we ensure that writing from serveral sources in parallel works as desired - especially in combination with gateways, where some of them repeat writing in a timer cycle regardless of a value change.Unabhängig von der Sollwertquelle können über das HMI oder auch eine Fernbedienung verschiedene Parameter eingestellt werden. Der Schreibzugriff ist dabei in der Regel parallel zum CIF-Modul möglich. Hierbei gewinnt der letzte Befehl, unabhängig von der Quelle. Damit dies funktioniert, werden Eingangswerte zur Pumpe nur bei Änderung geschrieben. Wollen Sie einen bestimmten Wert über die Schnittstelle forcieren, so ist zunächst aktive Wert zu lesen, zu schreiben und dann der gewünschte Wert zu schreiben. Nur so ist gewährleistet, dass ein Schreiben aus verschiedenen Quellen funktioniert - insbesondere in Verbindung mit Gateways, die zum Teil zyklisch schreiben.
To monitor a change of value from HMI or remote control, the "active" value can be read from the pump and compared with the current value to be written.Um einen Wertänderung vom HMI oder über eine Fernbedienung zu erkennen, kann der aktive Wert aus der Pumpe gelesen werden und mit dem eigenen Schreibwert verglichen werden.
To allow a glitch free switchover between two duty points, independent sets of input signals are available. For normal operation you may use the ones without special purpose. For an auxiliary set, you may use the ones with special purpose ´aux´. The ones with special purpose ´preset` are used for fallback by the bus command timer. Für eine störungsfreie Umschaltung zwischen zwei Arbeitspunkten sind unabhängige Sets von Eingangsvariablen verfügbar. Für den Normalbetrieb könnnen Sie die Variable ohne Sonderfunktion verwenden. für einen zweiten Arbeitspunkt sind die Variablen mit der Sonderfunktion ´aux´ verfügbar. Die Variablen mit der Sonderfunktion ´preset´ werden als Rückfallwerte in Verbindung mit dem Bus Command Timer verwendet.
Name | register typeRegister-Typ | Address | special purposeSonderfunktion |
---|---|---|---|
duty point (rel.) | Holding_register | 1 | |
duty point (rel.) aux. | Holding_register | 412 | aux. |
duty point (rel.) preset | Holding_register | 402 | preset |
Pump on | Holding_register | 40 | |
Pump on aux. | Holding_register | 414 | aux. |
Pump on preset | Holding_register | 404 | preset |
Control Function | Holding_register | 42 | |
Control Function aux. | Holding_register | 413 | aux. |
Control Function preset | Holding_register | 403 | preset |
Setpoint Signal Source | Holding_register | 401 | |
Setpoint Signal Source aux. | Holding_register | 415 | aux. |
Setpoint Signal Source preset | Holding_register | 405 | preset |
nameName | objectObjekt | special purposeSonderfunktion |
---|---|---|
Bus Setpoint in | analog-output 0 | |
duty point (rel.) aux. in | analog-output 200 | aux. |
duty point (rel.) preset in,A | analog-output 100 | preset |
Bus Command Pump on in | binary-output 0 | |
Pump on aux. in | binary-output 200 | aux. |
Preset Command Pump on preset in,A | binary-output 100 | preset |
Bus Control Mode in | multistate-output 0 | |
Control Function aux. in | multistate-output 200 | aux. |
Control Function preset in,A | multistate-output 100 | preset |
Setpoint Signal Source in | multistate-output 3 | |
Setpoint Signal Source aux. in | multistate-output 203 | aux. |
Setpoint Signal Source preset in,A | multistate-output 101 | preset |
The following table explains the different ´function` values for each datapoint:Die folgende Tabelle erläutert den Zusammenhang zwischen den verschieden Werten der Zeile ´Funktion` bei den Datenpunkt-Beschreibungen:
symbolSymbol | Name: Beschreibung |
---|---|
A | Rücklesewert Eingang (A): dieser Wert ist entweder der Eingangswert selbst, oder aber ein direkt davon abgeleiteter (z.B. aktuelle Grenzen für den Eingangswert). In jedem Fall ist der Wert vor einem eventuell vorhandenem Parameter-Selektor gemeint. |
A | readback input value (A): this value is either the input value itself or a value which is directly derived from the input value (e.g. a limit for the input value) |
B | value after parameter set selector (B): this value is read after signal processing by an optionally available parameter set selector |
B | Wert nach Parametersatz-Selektor (B): dieser Wert wird nach der Verarbeitung durch einen optionalen Parametersatz-Selektor gelesen |
active | aktiver Wert: dieser Wert ist im Gerät aktiv und ist der tatsächlich benutzte Wert für eine Funktion (z. B. begrenzter Sollwert) |
active | active value: this value is actively used in the device (e. g. limited setpoint) |
in | Eingangswert: dieser Wert wird in das Gerät geschrieben (z. B. Sollwert, Schaltbefehl, Parameter) |
in | input value: this value is written to the device (e.g. setpoint, command or parameter) |
out | Ausgangswert: dieser Wert ist das Ergebnis des Prozesses im Gerät (z. B. Prozesserte wie Durchfluss, Temperatur, aber auch der tatsächliche Arbeitspunkt, der sich aus dem Eingangswert 'Sollwert' ergibt) |
out | output value: this value is the result of the processing inside device |
Interfaces/ modulesSchnittstellen/Module | Ext. Off Stratos | Ext. Min Stratos | Ext. Off/SBM Stratos | SBM Stratos | DP Stratos | Modbus Stratos | BACnet Stratos | CAN Stratos | LON Stratos | PLR Stratos | Smart-IF Stratos |
---|---|---|---|---|---|---|---|---|---|---|---|
InterfacesSchnittstellen | |||||||||||
dry contact inputKontakteingang | • | • | • | ||||||||
dry contact outputPotentialfreier Kontakt | • | • | |||||||||
analog input 0…10 VAnalogeingang 0…10 V | • | • | • | ||||||||
digital sensor interfacedigitale Sensor-Schnittstelle | • | ||||||||||
CAN 2.0A | • | • | |||||||||
RS485 | • | • | |||||||||
LON TP/FT-10 | • | ||||||||||
Bluetooth LE | • | ||||||||||
WILO PLR | • | ||||||||||
dual pumpDoppelpumpe | • | • | • | • | • | • | • | • | • | • | |
FunctionsFunktionen | |||||||||||
Override OFF controlVorrang Aus | • | • | |||||||||
Override Min controlVorrang Min | • | ||||||||||
Setpoint ControlSollwert-Steuerung | • | • | • | • | • | • | • | • | • | ||
run signal (SBM)Betriebsmeldung (SBM) | • | • | • | • | • | • | • | • | |||
BACnet | • | ||||||||||
Modbus RTU | • | ||||||||||
CANopen | • | ||||||||||
WILO Net | • | ||||||||||
digital temperature inputdigitaler Temperatureingang | 2 |
Generally the pump is controlled by three parameters.Die Pumpe wird mit drei Parametern gesteuert.
The first is the setpoint which is scaled in percent. The maximum (100 %) values can be found at 21A1h (CONST_SPEED) 21A5h (VAR_DIFFPRSS) or 21ADh (CONST_PRESS / CONST_DIFFPRESS) Der erste Parameter ist der Sollwert, skaliert in %. Die Maximalwerte für die einzelnen Regelungsarten finden sich im Objekt 21A1h (CONST_SPEED) 21A5h (VAR_DIFFPRSS) bzw. 21ADh (CONST_PRESS / CONST_DIFFPRESS)
The second is the control mode which selects between constant speed (CONST_SPEED), constant (differential) pressure (CONST_PRES / CONST_DIFFPRESS) and other modes.Der zweite Parameter ist die Betriebsart und kann zwischen konstanter Drehzahl (CONST_SPEED), konstantem (Differenz-)Druck (CONST_PRESS / CONST_DIFFPRESS) und ggfs. weiteren ausgewählt werden.
The third parameter is the command which generally swiches the pump on or off.Der dritte Parameter ist das Kommando, welches die Pumpe EIN oder AUS schaltet.
Depending on the type of CAN communication you have to use different parameter sets. If you use simple control (more static , as described in 6.2.2) then the parameter set starting at 2000h is preferrable. If you use CANopen PDO mechanism the the parameters starting at 2008h are to be used.Abhängig von der Art der Kommunikation (PDO/SDO) müssen verschiedene Parametersätze verwendet werden. Wenn sie nur sporadisch steuern wollen (quasi-statisch, siehe Abschnitt 6.2.2), dann sind die Parameter ab 2000h zu bevorzugen. Wenn Sie den CANopen PDO Mechanismus verwenden wollen, dann sind die Parameter ab 2008h zu verwenden.
The readback of the parameters can be found starting with 2048h (selected ...).Die Rücklesewerte der Steuerungsparameter finden sich ab Objekt 2048h (selected ...).
The feedback (the really active) parameters can be found starting with 2040h (effective…)Die tatsächlich verwendeten Steuerungsparameter finden sich ab 2040h (effective…)
For a very simple operation you might use SDO writes as follows:Für eine einfache Steuerung können Sie die SDO Schreibbefehle wie folgt verwenden :
Normally you would use a PLC with an .eds file import for your application.Im Normalfall wird für die Steuerung eine SPS verwendet. Dort (oder mit einem separatem Bus-Konfigurationstool) kann die .eds Datei für Ihre Applikation eingelesen werden.
First of all you have to check if the system supports MPDOs. If not, you should use the .eds file …_no_MPDO.eds. You should map the control parameters starting at 2008h into yor system and the values you desire. Please ensure that the systems sends out heartbeats and the parameter 1016h is configured correctly.Zunächst prüfen Sie bitte, ob Ihr System MPDOs unterstützt. Falls nicht, benutzen Sie bitte die .eds Dateien mit der Kennung …_noMPDO.eds. Sie sollten die Steuerungsparamter ab 2008h und die von Ihnen gewünschten Lesewerte in die PDOs mappen. Stellen Sie sicher, dass Ihr System die Heartbeatüberwachung aktiviert hat und der Parameter 1016h der Pumpe korrekt konfiguriert ist.
Normally the pump is configured to send out TPDO3 as an MPDO.In der Werkseinstellung ist die Pumpe so konfiguriert, dass sie den TPDO3 als MPDO schickt.
If your system supports MPDOs, the functionality can be defined in the system. If not, you may extract the data manually:Wenn Ihr System MPDOs unterstützt, kann die Funktionalität dort definiert werden. Wenn nicht, können Sie die Daten aus dem MPDO manuell extrahieren:
This Modbus implementation supports the function codes 03, 04, 06 and 16.Diese Modbus-Implementierung unterstützt die Funktionscodes 03, 04, 06 und 16.
NOTE: All register addresses are raw addresses as they are transferred over the trunk. Sometimes an offset of 1 applies.HINWEIS: Alle Register-Adressen sind Rohwerte, wie sie über die Busleitung gesendet werden. In manchen Systemen ergibt sich dadurch ein Offset von 1.
addressAdresse | nameName |
---|---|
1 | duty point (rel.) |
40 | Pump Command in |
42 | Control Function |
44 | Δp-c = f(T) Regulation Tmin |
45 | Δp-c = f(T) Regulation Tmax |
46 | Δp-c = f(T) Regulation Δp(Tmin) |
47 | Δp-c = f(T) Regulation Δp(Tmax) |
300 | Bus Command Timer |
302 | temperature reference T1 |
304 | temperature reference T2 |
306 | sensor signal |
400 | Bus Command Timer Timeout |
401 | Setpoint Signal Source |
402 | duty point (rel.) preset |
403 | Control Function preset |
404 | Pump Command preset |
405 | Setpoint Signal Source preset |
408 | PID Kp |
409 | PID Ti |
410 | PID Td |
412 | duty point (rel.) aux. |
413 | Control Function aux. |
414 | Pump Command aux. |
415 | Setpoint Signal Source aux. |
416 | parameter set selector |
420 | Flow (calculated) limit. max |
422 | Flow (calculated) limit. min |
424 | Flow (calculated) limit. off |
426 | Flow zero setpoint red. factor |
427 | Flow nominal for Ctrl. Fun. |
847 | Flow replacement value |
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 1 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 40 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Pump on | Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den normalen Einschaltbefehl. Er wird umgesetzt, wenn keine Übersteuerungsfunktionen aktiv sind. | This is the base signal. This signal represents the normal "ON" command. This signal is effektive, if no override functions are active. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | Override min | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "MIN" Befehl. | This is the base signal. This signal overrides the pump (system) command with "MIN" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
2 | Override max | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "MAX" Befehl. | This is the base signal. This signal overrides the pump (system) command with "MAX" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | TRUE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '1' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer gesetzt sein. | This is the base signal. This signal represens a static '1' bit, typically for compatibility purpose. For write acces, this bit shall always be '1'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
4 | Override off | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "OFF" Befehl. | This is the base signal. This signal overrides the pump (system) command with "OFF" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
5 | Override on | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "ON" Befehl. | This is the base signal. This signal overrides the pump (system) command with "ON" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
6 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
7 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
8 | Auto Night Mode | Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert die automatische Absenkfuntion. Diese zwingt das Gerät, nicht mehr mit der Sollwertvorgabe, sondern mit niedrigeren Werten zu arbeiten. | This is the base signal. This signal represents the automatic setback mode . This mode forces the device to run at lower settings than the normal duty point. | GLANDLESS, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register steuert die Pumpe. Sie kann ein- bzw. ausgeschaltet werden oder auch mit Minimal- oder Maximalwerten übersteuert werden.This is the base signal. This register controls the pump. It can be switched on or off. furthermore, the on/off command can be overridden with min or max values.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 42 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | Gen_Spd | This control mode operates the device with constant speed.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
2 | CONST_FREQ | reservedreserviert | − |
3 | Gen_PHdConst | This control mode operates the device with constant differential pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
4 | Gen_PHdVar | This control mode operates the device with a differential pressure which varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
5 | Gen_PConst | This control mode operates the device with constant discharge pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Ausgangsdruck. | MVIE, …; |
6 | TEMP_VARIABLE | This control mode operates the device with a differential pressure which varies with the fluid temperature.Diese Steuerungsart betreibt das Gerät mit mediumstemperaturabhängigem Differenzdruck (Δp-c=F(T)) . | CIF-/IF-Module internal; Stratos; |
6 | CONST_POWER | reservedreserviert | − |
7 | CONST_HEAD | reservedreserviert | − |
8 | CONST_FLOW | reservedreserviert | − |
9 | Gen_T | This control mode operates the device with constant temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
10 | Gen_TDiff | This control mode operates the device with constant differential temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
11 | CONST_LEV | reservedreserviert | − |
15 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
16 | HeatRadiator_PHd | This control mode operates the device with a differential pressure which varies with the flow for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
17 | HeatRadiator_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
18 | HeatRadiator_T | This control mode operates the device with constant temperature for heating radiator application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
19 | HeatFloor_PHd | This control mode operates the device with a differential pressure for floor heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
20 | HeatFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
21 | HeatFloor_T | This control mode operates the device with constant temperature for floor heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
22 | HeatCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
23 | HeatCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
24 | HeatCeiling_T | This control mode operates the device with constant temperature for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
25 | HeatFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
26 | HeatFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
27 | HeatFan_T | This control mode operates the device with constant temperature for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
28 | HeatB._T | This control mode operates the device with constant temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
29 | HeatB._TDiff | This control mode operates the device with constant differential temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
30 | HeatB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
31 | HeatE._T | This control mode operates the device with constant temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
32 | HeatE._TDiff | This control mode operates the device with constant differential temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
33 | HeatE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
34 | Heat_PHdConst | This control mode operates the device with constant differential pressure for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
35 | Heat_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
36 | Heat_PHdExt | This control mode operates the device with constant differential pressure for heating applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
37 | Heat_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
38 | Heat_VolFlow | This control mode operates the device with constant volume flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
39 | Heat_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
40 | Heat_T | This control mode operates the device with constant temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
41 | Heat_TDiff | This control mode operates the device with constant differential temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
42 | Heat_Spd | This control mode operates the device with constant speed for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
43 | CoolCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
44 | CoolCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
45 | CoolCeiling_T | This control mode operates the device with constant temperature for ceiling refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
46 | CoolFloor_PHd | This control mode operates the device with constant differential pressure for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
47 | CoolFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
48 | CoolFloor_T | This control mode operates the device with constant temperature mode for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
49 | CoolFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstronmabhängigem Differenzdruck für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
50 | CoolFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
51 | CoolFan_T | This control mode operates the device with constant temperature mode for fan coil refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
52 | CoolB._T | This control mode operates the device with constant temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
53 | CoolB._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
54 | CoolB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
55 | CoolE._T | This control mode operates the device with constant temperature mode for refrigeration application with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungs-Anwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
56 | CoolE._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
57 | CoolE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with heat exhanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Wärmetauscher | Stratos MAXO; Stratos GIGA 2.0; |
58 | Cool_PHdConst | This control mode operates the device with constant differential pressure for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
59 | Cool_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
60 | Cool_PHdExt | This control mode operates the device with constant differential pressure for refrigeration application with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
61 | Cool_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
62 | Cool_VolFlow | This control mode operates the device with constant volume flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
63 | Cool_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen | Stratos MAXO; Stratos GIGA 2.0; |
64 | Cool_T | This control mode operates the device with constant temperature mode for refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
65 | Cool_TDiff | This control mode operates the device with constant differential temperature for cooling application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
66 | Cool_Spd | This control mode operates the motor with constant speed for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
67 | San_Circ._T | This control mode operates the device with constant temperature for sanitary hot water circulation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Zirkulations-Anwendungen. | Stratos MAXO; |
68 | SanW.Heat._TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application with heat exchanger in the storage tank.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen mit Wärmetauscher im Warmwasserspeicher | Stratos MAXO; Stratos GIGA 2.0; |
69 | SanL.S._T | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
70 | SanL.S._Acc.Flow | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
71 | San_PHdConst | This control mode operates the device with constant differential pressure for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
72 | San_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
73 | San_PHdExternal | This control mode operates the device with constant differential pressure for sanitary hot water applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
74 | San_VolFlow | This control mode operates the device with constant volume flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
75 | San_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Trink-Warmwasser-Anwendungen | Stratos MAXO; Stratos GIGA 2.0; |
76 | San_T | This control mode operates the device with constant temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
77 | San_TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
78 | San_Spd | This control mode operates the motor with constant speed for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
79 | Gen_PHdExt | This control mode operates the device with constant differential pressure for generic applications with external diffential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
80 | Gen_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for generic applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
81 | Gen_VolFlow | This control mode operates the device with constant volume flow for generic applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
82 | Gen_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for generic applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
83 | ScndPHdConst | This control mode operates the device with constant differential pressure. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
84 | ScndPHdVar | This control mode operates the device with a differential pressure which varies with the flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
85 | ScndFlow | This control mode operates the device with constant volume flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
86 | ScndSpd | This control mode operates the motor with constant speed. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
87 | HeatConcrete_PHd | This control mode operates the device with a differential pressure for concrete core activation heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
88 | HeatConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
89 | HeatConcrete_TDiff | This control mode operates the device with constant differential temperature for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
90 | HeatConcrete_Flow | This control mode operates the device with constant volume flow for heating applications with concrete core activation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
91 | HeatBottle_Flow | This control mode operates the device with constant volume flow for heating applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
92 | HeatMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
93 | HeatMan_Flow | This control mode operates the device with constant volume flow for heating applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
94 | HeatTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with storage tank.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
95 | HeatTank_Flow | This control mode operates the device with constant volume flow for heating applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
96 | HeatExchanger_Flow | This control mode operates the device with constant volume flow for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
97 | HeatSource_TDiff | This control mode operates the device with constant differential temperature for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
98 | HeatSource_Flow | This control mode operates the device with constant volume flow for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
99 | HeatDistrict_PHdConst | This control mode operates the device with a differential pressure for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
100 | HeatDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
101 | HeatDistrict_PHdExt | This control mode operates the device with constant differential pressure for district heating application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernwärme-Anwendungen. | Stratos GIGA 2.0; |
102 | CoolConcrete_PHd | This control mode operates the device with a differential pressure for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
103 | CoolConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
104 | CoolConcrete_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
105 | CoolConcrete_Flow | This control mode operates the device with constant volume flow for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
106 | CoolBottle_Flow | This control mode operates the device with constant volume flow for refrigeration applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
107 | CoolMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
108 | CoolMan_Flow | This control mode operates the device with constant volume flow for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
109 | CoolTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
110 | CoolTank_Flow | This control mode operates the device with constant volume flow for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
111 | CoolExchanger_Flow | This control mode operates the device with constant volume flow for refrigeration applications with heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
112 | CoolCondenser_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with recirculating cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
113 | CoolCondensor_Flow | This control mode operates the device with constant volume flow for refrigeration applications with recirculationg cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
114 | CoolDistrict_PHdConst | This control mode operates the device with a differential pressure for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
115 | CoolDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
116 | CoolDistrict_PHdExt | This control mode operates the device with constant differential pressure for district refrigeration application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernkühlungs-Anwendungen. | Stratos GIGA 2.0; |
117 | 108_RESERVED | reserved for future use reserviert | − |
118 | 109_RESERVED | reserved for future use reserviert | − |
139 | Gen_PVar | This control mode operates the device with a discharge pressure that varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigen Ausgangsdruck. | MVIE, …; |
140 | Gen_UsrDfd | This control mode operates the device with user configurable PID controller.Diese Steuerungsart betreibt das Gerät mit einem frei konfigurierbaren PID-Regler für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; IL_E, …; MVIE, …; |
Dieses Signal ist das Grundsignal. Dieses Signal beinhaltet die Steuerungsart für das Gerät. Wird eine gewählte Steuerungsart nicht unterstützt, bleibt das Gerät bei der zuletzt eingestellten Steuerungsart.This is the base signal. This signal represents the control mode for the device. In case a selected mode is not supported, the device will stay in the previously selected mode.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 44 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | UINT |
unitEinheit | K |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Parameter setzt die untere Grenztemperatur für die temperaturabhängige Druckregelung. Unterhalb dieser Temperatur bleibt der Diffenzdruck konstant. Weil dieser Wert immer um mindestens 10 K niedriger sein muss als der Wert für Tmax, wird bei einem Schreibzugriff Tmax immer automatisch mit angepasst.This is the base signal. This Parameter sets the lower temperature limit for temperature dependent pressure control. Below this temperature, the head is always constant Since this value must always be at least 10 K smaller than Tmax, the value Tmax is always set to 10 K higher than this value with every write access.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal; Stratos;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 45 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | UINT |
unitEinheit | K |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Parameter setzt die obere Grenztemperatur für die temperaturabhängige Druckregelung. Über dieser Temperatur bleibt der Diffenzdruck konstant. Weil dieser Wert immer um mindestens 10 K höher sein muss als der Wert für Tmin, wird Tmin bei einem Schreibzugriff immer automatisch angepasst.This is the base signal. This Parameter sets the upper limit for temperature dependent pressure head control. The head above this temperature is constant. Since this value must always be at least 10 K higher than Tmin, the value Tmin is always set to at least 10 K lower than this value.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal; Stratos;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 46 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Parameter gehört zur Betriebsart Δp-c = f(T). Er setzt den Druck bei der Minimaltemperatur Tmin und darunter. Der Wert kann höher oder niedriger als der Wert von Δp(Tmax) sein.This is the base signal. This parameter belongs to the operation mode Δp-c = f(T). It sets the presssure at and below the temperature Tmin. This value can be higheer or lower than the value of Tmax.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal; Stratos;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 47 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Parameter gehört zur Betriebsart Δp-c = f(T). Er setzt den Druck bei der oberen Grenz-Temperatur Tmax und darüber. Der Wert kann höher oder niedriger als der Wert von Δp(Tmax) sein.This is the base signal. This parameter belongs to the operation mode Δp-c = f(T). It sets the presssure at and above the temperature Tmax. This value can be higher or lower than the value of Δp(Tmin).
Support reference: Wird unterstützt durch: CIF-/IF-Module internal; Stratos;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 300 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | BYTE |
range lowBereich min. | 1 |
range highBereich max. | 10 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | OFF | The functionality Bus Command timer is deactivated. The local operation is blocked permanently.Die Funktion Bus Command Timer ist deaktiviert. Die lokale Pumpenbedienung ist dauernd gesperrt. | CIF-/IF-Module internal; |
2 | SET | This value starts a lockout time for the local pump operation. The lockout time may be adjustable.Dieser Wert startet eine Sperrzeit für die lokale Pumpenbedienung. Die Sperrzeit ist ggfs. einstellbar. | CIF-/IF-Module internal; |
3 | ACTIVE | This value indicates that the lockout time is active.Dieser Wert zeigt an, dass die Sperrzeit, die mit dem Signal "Bus Command Timer SET" aktiviert wurde, derzeit läuft. | CIF-/IF-Module internal; |
4 | RESET | This value indicates that the lockout time which was started with the signal "Bus Command Timer SET" has elapsed. Local operation of the device is possible, the write to the device over the communication interface is blocked.Dieser Wert zeigt an, dass die Sperrzeit, die mit dem Signal "Bus Command Timer SET" aktiviert wurde, abgelaufen ist. Die lokale Bedienung ist möglich, das Schreiben über die Kommunikationsschnittstelle ist gesperrt. | CIF-/IF-Module internal; |
5 | MANUAL | This value indicates that the local as well as the remote operation is possible. The commands are accepted according "last write wins".Dieser Wert zeigt an, dass sowohl die lokale Bedienung, als auch die Bedienung über die Kommunikationsverbindung möglich ist. Der letzte Befehl wird übernommen. | CIF-/IF-Module internal; |
6 | SET_PRESET | This value starts a lockout time for the local pump operation. After the lockout time has elapsed, PRESET values are used for operation. The lockout time may be adjustable.Dieser Wert startet eine Sperrzeit für die lokale Pumpenbedienung. Nach Ablauf der Sperrzeit werden voreingestellte Werte (PRESET) als Vorgabe gesetzt. Die Sperrzeit ist ggfs. einstellbar. | CIF-/IF-Module internal; |
7 | ACTIVE_PRESET | This value indicates that the lockout time which was started with the signal "Bus Command Timer SET_PRESET" is currently active. After the lockout time has elapsed, PRESET values are used for operation.Dieser Wert zeigt an, dass die Sperrzeit, welche mit dem Signal "Bus Command Timer SET" aktiviert wurde, derzeit läuft. Nach Ablauf der Sperrzeit werden voreingestellte Werte (PRESET) als Vorgabe gesetzt. | CIF-/IF-Module internal; |
8 | RESET_PRESET | This value indicates that the lockout time which was started with the signal "Bus Command Timer SET" has elapsed. Local operation of the device is possible, the write to the device over the communication link is blocked. When this signal becomes ative, PRESET values are set once for operation.Dieser Wert zeigt an, dass die Sperrzeit, die mit dem Signal "Bus Command Timer SET" aktiviert wurde, abgelaufen ist. Die lokale Bedienung ist möglich, das Schreiben über das Kommunikationsinterface ist gesperrt. Sobald dises Signal aktiv wird, werden einmalig voreingestellte Werte (PRESET) als Vorgabe gesetzt. | CIF-/IF-Module internal; |
9 | MANUAL_PRESET | This value indicates that the local as well as the remote operation is possible. The commands are accepted according "last write wins". When this signal becomes active, PRESET values are loaded once.Dieser Wert zeigt an, dass sowohl die lokale Bedienung, als auch die Bedienung über die Kommunikationsverbindung möglich ist. Der letzte Befehl wird übernommen. Wenn dieser Wert aktiv wird, werden einmalig PRESET Werte als Vorgabe übernommen. | CIF-/IF-Module internal; |
10 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Wenn ein IF-Modul benutzt wird, ist in der Werkseinstellung das Menü der Pumpe ggfs. verriegelt. Beim Wert MANUAL ist das Menü dauerhaft freigegeben. Um das lokale Menü nur bei Feldbus-Ausfall zu öffen, schreiben Sie den Wert SET immer innerhalb der optional verfügbaren Bus Command Timer timeout Zeit (default bzw. fester Wert von 300 s). Die Aktivierung wird gespeichert und überlebt einen Spannungsreset. Wenn der Mechanismus nicht mehr benötigt wird, schreiben Sie OFF, um zur Werkseinstellung zurückzukehren. Wenn der Bus Command Timer abläuft, wird ggfs. E54 im Display angezeigt. Dann können im Menü Einstellungen vorgenommen werden. Um bei einem Bus-Ausfall nicht nur die lokale Bedienung zu erlauben, sondern auch Rückfall- (Fallback) Werte zu laden, schreiben Sie statt SET SET_PRESET. Die Fallback-Werte sind in separaten Datenpunkten realisiert und haben "PRESET" im Namen. Diese Funktion ist bei IF-Modulen erst ab SW > 2.00 realisiert, bei CIF-Modulen ist sie immer vorhanden. This is the base signal. When using an IF-Module the local menu may be disabled by factory setting. The local menu can be enabled permanently by writing the value MANUAL. To use the local menu only when the BAS system fails, repeate writing the value SET at least before the optional Bus Command Timer timeout time (default or fixed value 300 s). The activation is stored and survives a power on reset. When the mechanism is no longer needed, write OFF to reset to factory setting. If the BAS fails,Then the menu can be entered to adjust the settings. E50 may be displayed at the pump. If it is desired to load fallback values when the bus failure event occures, then use SET_PRESET instead of SET to trigger the bus command timer. This functionality is available with Modbus and BACnet in IF-modules starting with firmware SW > 2.00. For CIF-modules, there is no restriction.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 302 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | REAL |
unitEinheit | K |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die erste Bezugstemperatur (T1) des hydraulischen Kreises für Regelungszwecke.This is the base signal. This signal represents the first fluid reference temperature (T1) of the hydronic circuit for control purposes.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 304 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | REAL |
unitEinheit | K |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die zweite Bezugstemperatur (T2) des hydraulischen Kreises für Regelungszwecke.This is the base signal. This signal represents the second fluid reference temperature (T2) of the hydronic circuit for control purposes.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 306 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | REAL |
unitEinheit | - |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal definiert einen Sensorwert für Regelungszwecke. Skalierung und Einheit entsprechen der aktuellen Regelungsfunktion.This is the base signal. This signal defines a sensor value for closed loop control applications. Scaling and physical unit are corresponding to the current control function
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 400 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | UINT |
unitEinheit | s |
scaleSkalierung | 1 |
range lowBereich min. | 20 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Dieser Wert setzt die Timeout-Zeit für den Bus Command Timer. Diese Funktion ist bei IF-Modulen Modbus und BACnet erst ab Software SW > 2.00 vorhanden. Ist dieser Datenpunkt nicht vorhanden, gilt eine fest eingestellte Zeit von 300 s. Der Minimalwert ist 20 s.This is the base signal. This value sets the timeout for the Bus Command Timer. Minimum value is 20 s; factory default is 300 s.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 401 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | IF-Module | Signal source for setpoint: IF-ModuleSollwertquelle IF-Modul | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …; |
2 | 0…10 V | Signal source for setpoint: IN2 mode 0…10 VSollwertquelle: IN2 Modus 0…10 V | CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …; |
3 | 2…10 V | Signal source for setpoint: IN2 mode 2…10 VSollwertquelle: IN2 Modus 2…10 V | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
4 | 0…20 mA | Signal source for setpoint: IN2 mode 0…20 mASollwertquelle: IN2 Modus 0…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
5 | 4…20 mA | Signal source for setpoint: IN2 mode 4…20 mASollwertquelle: IN2 Modus 4…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
6 | Internal | Signal source for setpoint: internalSollwertquelle: Intern | Stratos MAXO; Stratos GIGA 2.0; |
7 | EXT 1 | Signal source for setpoint: EXT 1Sollwertquelle: EXT 1 | Stratos MAXO; Stratos GIGA 2.0; |
8 | EXT 2 | Signal source for setpoint: EXT 2Sollwertquelle: EXT 2 | Stratos MAXO; Stratos GIGA 2.0; |
9 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Dieses Signal enthält die Sollwertquelle in der aktuellen Regelungsart. This is the base signal. This signal represents the source for the setpoint for the current control function.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 402 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / readback input value (A)Eingangswert / Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dies beinhaltet eine Voreinstellung für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This incorporates a preset or fallback function for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 403 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / readback input value (A)Eingangswert / Rücklesewert Eingang (A) |
data typeDatentyp | WORD |
range lowBereich min. | 0 |
range highBereich max. | 140 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | Gen_Spd | This control mode operates the device with constant speed.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
2 | CONST_FREQ | reservedreserviert | − |
3 | Gen_PHdConst | This control mode operates the device with constant differential pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
4 | Gen_PHdVar | This control mode operates the device with a differential pressure which varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
5 | Gen_PConst | This control mode operates the device with constant discharge pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Ausgangsdruck. | MVIE, …; |
6 | TEMP_VARIABLE | This control mode operates the device with a differential pressure which varies with the fluid temperature.Diese Steuerungsart betreibt das Gerät mit mediumstemperaturabhängigem Differenzdruck (Δp-c=F(T)) . | CIF-/IF-Module internal; Stratos; |
6 | CONST_POWER | reservedreserviert | − |
7 | CONST_HEAD | reservedreserviert | − |
8 | CONST_FLOW | reservedreserviert | − |
9 | Gen_T | This control mode operates the device with constant temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
10 | Gen_TDiff | This control mode operates the device with constant differential temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
11 | CONST_LEV | reservedreserviert | − |
15 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
16 | HeatRadiator_PHd | This control mode operates the device with a differential pressure which varies with the flow for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
17 | HeatRadiator_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
18 | HeatRadiator_T | This control mode operates the device with constant temperature for heating radiator application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
19 | HeatFloor_PHd | This control mode operates the device with a differential pressure for floor heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
20 | HeatFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
21 | HeatFloor_T | This control mode operates the device with constant temperature for floor heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
22 | HeatCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
23 | HeatCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
24 | HeatCeiling_T | This control mode operates the device with constant temperature for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
25 | HeatFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
26 | HeatFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
27 | HeatFan_T | This control mode operates the device with constant temperature for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
28 | HeatB._T | This control mode operates the device with constant temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
29 | HeatB._TDiff | This control mode operates the device with constant differential temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
30 | HeatB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
31 | HeatE._T | This control mode operates the device with constant temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
32 | HeatE._TDiff | This control mode operates the device with constant differential temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
33 | HeatE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
34 | Heat_PHdConst | This control mode operates the device with constant differential pressure for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
35 | Heat_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
36 | Heat_PHdExt | This control mode operates the device with constant differential pressure for heating applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
37 | Heat_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
38 | Heat_VolFlow | This control mode operates the device with constant volume flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
39 | Heat_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
40 | Heat_T | This control mode operates the device with constant temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
41 | Heat_TDiff | This control mode operates the device with constant differential temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
42 | Heat_Spd | This control mode operates the device with constant speed for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
43 | CoolCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
44 | CoolCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
45 | CoolCeiling_T | This control mode operates the device with constant temperature for ceiling refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
46 | CoolFloor_PHd | This control mode operates the device with constant differential pressure for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
47 | CoolFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
48 | CoolFloor_T | This control mode operates the device with constant temperature mode for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
49 | CoolFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstronmabhängigem Differenzdruck für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
50 | CoolFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
51 | CoolFan_T | This control mode operates the device with constant temperature mode for fan coil refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
52 | CoolB._T | This control mode operates the device with constant temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
53 | CoolB._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
54 | CoolB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
55 | CoolE._T | This control mode operates the device with constant temperature mode for refrigeration application with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungs-Anwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
56 | CoolE._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
57 | CoolE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with heat exhanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Wärmetauscher | Stratos MAXO; Stratos GIGA 2.0; |
58 | Cool_PHdConst | This control mode operates the device with constant differential pressure for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
59 | Cool_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
60 | Cool_PHdExt | This control mode operates the device with constant differential pressure for refrigeration application with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
61 | Cool_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
62 | Cool_VolFlow | This control mode operates the device with constant volume flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
63 | Cool_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen | Stratos MAXO; Stratos GIGA 2.0; |
64 | Cool_T | This control mode operates the device with constant temperature mode for refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
65 | Cool_TDiff | This control mode operates the device with constant differential temperature for cooling application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
66 | Cool_Spd | This control mode operates the motor with constant speed for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
67 | San_Circ._T | This control mode operates the device with constant temperature for sanitary hot water circulation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Zirkulations-Anwendungen. | Stratos MAXO; |
68 | SanW.Heat._TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application with heat exchanger in the storage tank.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen mit Wärmetauscher im Warmwasserspeicher | Stratos MAXO; Stratos GIGA 2.0; |
69 | SanL.S._T | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
70 | SanL.S._Acc.Flow | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
71 | San_PHdConst | This control mode operates the device with constant differential pressure for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
72 | San_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
73 | San_PHdExternal | This control mode operates the device with constant differential pressure for sanitary hot water applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
74 | San_VolFlow | This control mode operates the device with constant volume flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
75 | San_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Trink-Warmwasser-Anwendungen | Stratos MAXO; Stratos GIGA 2.0; |
76 | San_T | This control mode operates the device with constant temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
77 | San_TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
78 | San_Spd | This control mode operates the motor with constant speed for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
79 | Gen_PHdExt | This control mode operates the device with constant differential pressure for generic applications with external diffential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
80 | Gen_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for generic applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
81 | Gen_VolFlow | This control mode operates the device with constant volume flow for generic applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
82 | Gen_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for generic applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
83 | ScndPHdConst | This control mode operates the device with constant differential pressure. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
84 | ScndPHdVar | This control mode operates the device with a differential pressure which varies with the flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
85 | ScndFlow | This control mode operates the device with constant volume flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
86 | ScndSpd | This control mode operates the motor with constant speed. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
87 | HeatConcrete_PHd | This control mode operates the device with a differential pressure for concrete core activation heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
88 | HeatConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
89 | HeatConcrete_TDiff | This control mode operates the device with constant differential temperature for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
90 | HeatConcrete_Flow | This control mode operates the device with constant volume flow for heating applications with concrete core activation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
91 | HeatBottle_Flow | This control mode operates the device with constant volume flow for heating applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
92 | HeatMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
93 | HeatMan_Flow | This control mode operates the device with constant volume flow for heating applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
94 | HeatTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with storage tank.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
95 | HeatTank_Flow | This control mode operates the device with constant volume flow for heating applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
96 | HeatExchanger_Flow | This control mode operates the device with constant volume flow for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
97 | HeatSource_TDiff | This control mode operates the device with constant differential temperature for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
98 | HeatSource_Flow | This control mode operates the device with constant volume flow for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
99 | HeatDistrict_PHdConst | This control mode operates the device with a differential pressure for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
100 | HeatDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
101 | HeatDistrict_PHdExt | This control mode operates the device with constant differential pressure for district heating application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernwärme-Anwendungen. | Stratos GIGA 2.0; |
102 | CoolConcrete_PHd | This control mode operates the device with a differential pressure for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
103 | CoolConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
104 | CoolConcrete_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
105 | CoolConcrete_Flow | This control mode operates the device with constant volume flow for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
106 | CoolBottle_Flow | This control mode operates the device with constant volume flow for refrigeration applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
107 | CoolMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
108 | CoolMan_Flow | This control mode operates the device with constant volume flow for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
109 | CoolTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
110 | CoolTank_Flow | This control mode operates the device with constant volume flow for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
111 | CoolExchanger_Flow | This control mode operates the device with constant volume flow for refrigeration applications with heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
112 | CoolCondenser_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with recirculating cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
113 | CoolCondensor_Flow | This control mode operates the device with constant volume flow for refrigeration applications with recirculationg cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
114 | CoolDistrict_PHdConst | This control mode operates the device with a differential pressure for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
115 | CoolDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
116 | CoolDistrict_PHdExt | This control mode operates the device with constant differential pressure for district refrigeration application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernkühlungs-Anwendungen. | Stratos GIGA 2.0; |
117 | 108_RESERVED | reserved for future use reserviert | − |
118 | 109_RESERVED | reserved for future use reserviert | − |
139 | Gen_PVar | This control mode operates the device with a discharge pressure that varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigen Ausgangsdruck. | MVIE, …; |
140 | Gen_UsrDfd | This control mode operates the device with user configurable PID controller.Diese Steuerungsart betreibt das Gerät mit einem frei konfigurierbaren PID-Regler für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; IL_E, …; MVIE, …; |
Dies beinhaltet eine Voreinstellung für das folgende Signal. Dieses Signal beinhaltet die Steuerungsart für das Gerät. Wird eine gewählte Steuerungsart nicht unterstützt, bleibt das Gerät bei der zuletzt eingestellten Steuerungsart.This incorporates a preset or fallback function for the following signal. This signal represents the control mode for the device. In case a selected mode is not supported, the device will stay in the previously selected mode.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 404 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Pump on preset | Dies beinhaltet eine Voreinstellung für das folgende Signal. Dieses Signal repräsentiert den normalen Einschaltbefehl. Er wird umgesetzt, wenn keine Übersteuerungsfunktionen aktiv sind. | This incorporates a preset or fallback function for the following signal. This signal represents the normal "ON" command. This signal is effektive, if no override functions are active. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal.This is the base signal.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 405 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / readback input value (A)Eingangswert / Rücklesewert Eingang (A) |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | IF-Module | Signal source for setpoint: IF-ModuleSollwertquelle IF-Modul | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …; |
2 | 0…10 V | Signal source for setpoint: IN2 mode 0…10 VSollwertquelle: IN2 Modus 0…10 V | CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …; |
3 | 2…10 V | Signal source for setpoint: IN2 mode 2…10 VSollwertquelle: IN2 Modus 2…10 V | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
4 | 0…20 mA | Signal source for setpoint: IN2 mode 0…20 mASollwertquelle: IN2 Modus 0…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
5 | 4…20 mA | Signal source for setpoint: IN2 mode 4…20 mASollwertquelle: IN2 Modus 4…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
6 | Internal | Signal source for setpoint: internalSollwertquelle: Intern | Stratos MAXO; Stratos GIGA 2.0; |
7 | EXT 1 | Signal source for setpoint: EXT 1Sollwertquelle: EXT 1 | Stratos MAXO; Stratos GIGA 2.0; |
8 | EXT 2 | Signal source for setpoint: EXT 2Sollwertquelle: EXT 2 | Stratos MAXO; Stratos GIGA 2.0; |
9 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
Dies beinhaltet eine Voreinstellung für das folgende Signal. Dieses Signal enthält die Sollwertquelle in der aktuellen Regelungsart. This incorporates a preset or fallback function for the following signal. This signal represents the source for the setpoint for the current control function.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 408 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | INT |
unitEinheit | - |
scaleSkalierung | 0.01 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Der Parameter Kp stellt den Verstärkungsfaktor des PID-Reglers der aktuellen Regelungsart dar.This is the base signal. The parameter Kp controls the gain of the PID closed loop controller.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 409 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | INT |
unitEinheit | s |
scaleSkalierung | 0.01 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Der Parameter Ti stellt die Integrationszeit des PID-Reglers dar. This is the base signal. The parameter Ti represent the integral time for the PID closed loop controller.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 410 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value / active valueEingangswert / aktiver Wert |
data typeDatentyp | INT |
unitEinheit | s |
scaleSkalierung | 0.01 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Der Parameter Td stellt die Vorhaltzeit des PID-Reglers dar.This is the base signal. The Td parameter represents the derivative time for the PID closed loop controller.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 412 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies definiert einen alternativen Wert für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This defines an alternative value for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 413 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | Gen_Spd | This control mode operates the device with constant speed.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
2 | CONST_FREQ | reservedreserviert | − |
3 | Gen_PHdConst | This control mode operates the device with constant differential pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
4 | Gen_PHdVar | This control mode operates the device with a differential pressure which varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
5 | Gen_PConst | This control mode operates the device with constant discharge pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Ausgangsdruck. | MVIE, …; |
6 | TEMP_VARIABLE | This control mode operates the device with a differential pressure which varies with the fluid temperature.Diese Steuerungsart betreibt das Gerät mit mediumstemperaturabhängigem Differenzdruck (Δp-c=F(T)) . | CIF-/IF-Module internal; Stratos; |
6 | CONST_POWER | reservedreserviert | − |
7 | CONST_HEAD | reservedreserviert | − |
8 | CONST_FLOW | reservedreserviert | − |
9 | Gen_T | This control mode operates the device with constant temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
10 | Gen_TDiff | This control mode operates the device with constant differential temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
11 | CONST_LEV | reservedreserviert | − |
15 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
16 | HeatRadiator_PHd | This control mode operates the device with a differential pressure which varies with the flow for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
17 | HeatRadiator_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
18 | HeatRadiator_T | This control mode operates the device with constant temperature for heating radiator application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
19 | HeatFloor_PHd | This control mode operates the device with a differential pressure for floor heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
20 | HeatFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
21 | HeatFloor_T | This control mode operates the device with constant temperature for floor heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
22 | HeatCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
23 | HeatCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
24 | HeatCeiling_T | This control mode operates the device with constant temperature for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
25 | HeatFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
26 | HeatFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
27 | HeatFan_T | This control mode operates the device with constant temperature for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
28 | HeatB._T | This control mode operates the device with constant temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
29 | HeatB._TDiff | This control mode operates the device with constant differential temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
30 | HeatB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
31 | HeatE._T | This control mode operates the device with constant temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
32 | HeatE._TDiff | This control mode operates the device with constant differential temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
33 | HeatE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
34 | Heat_PHdConst | This control mode operates the device with constant differential pressure for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
35 | Heat_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
36 | Heat_PHdExt | This control mode operates the device with constant differential pressure for heating applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
37 | Heat_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
38 | Heat_VolFlow | This control mode operates the device with constant volume flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
39 | Heat_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
40 | Heat_T | This control mode operates the device with constant temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
41 | Heat_TDiff | This control mode operates the device with constant differential temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
42 | Heat_Spd | This control mode operates the device with constant speed for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
43 | CoolCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
44 | CoolCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
45 | CoolCeiling_T | This control mode operates the device with constant temperature for ceiling refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
46 | CoolFloor_PHd | This control mode operates the device with constant differential pressure for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
47 | CoolFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
48 | CoolFloor_T | This control mode operates the device with constant temperature mode for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
49 | CoolFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstronmabhängigem Differenzdruck für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
50 | CoolFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
51 | CoolFan_T | This control mode operates the device with constant temperature mode for fan coil refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
52 | CoolB._T | This control mode operates the device with constant temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
53 | CoolB._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
54 | CoolB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
55 | CoolE._T | This control mode operates the device with constant temperature mode for refrigeration application with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungs-Anwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
56 | CoolE._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
57 | CoolE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with heat exhanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Wärmetauscher | Stratos MAXO; Stratos GIGA 2.0; |
58 | Cool_PHdConst | This control mode operates the device with constant differential pressure for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
59 | Cool_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
60 | Cool_PHdExt | This control mode operates the device with constant differential pressure for refrigeration application with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
61 | Cool_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
62 | Cool_VolFlow | This control mode operates the device with constant volume flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
63 | Cool_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen | Stratos MAXO; Stratos GIGA 2.0; |
64 | Cool_T | This control mode operates the device with constant temperature mode for refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
65 | Cool_TDiff | This control mode operates the device with constant differential temperature for cooling application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
66 | Cool_Spd | This control mode operates the motor with constant speed for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
67 | San_Circ._T | This control mode operates the device with constant temperature for sanitary hot water circulation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Zirkulations-Anwendungen. | Stratos MAXO; |
68 | SanW.Heat._TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application with heat exchanger in the storage tank.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen mit Wärmetauscher im Warmwasserspeicher | Stratos MAXO; Stratos GIGA 2.0; |
69 | SanL.S._T | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
70 | SanL.S._Acc.Flow | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
71 | San_PHdConst | This control mode operates the device with constant differential pressure for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
72 | San_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
73 | San_PHdExternal | This control mode operates the device with constant differential pressure for sanitary hot water applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
74 | San_VolFlow | This control mode operates the device with constant volume flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
75 | San_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Trink-Warmwasser-Anwendungen | Stratos MAXO; Stratos GIGA 2.0; |
76 | San_T | This control mode operates the device with constant temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
77 | San_TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
78 | San_Spd | This control mode operates the motor with constant speed for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
79 | Gen_PHdExt | This control mode operates the device with constant differential pressure for generic applications with external diffential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
80 | Gen_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for generic applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
81 | Gen_VolFlow | This control mode operates the device with constant volume flow for generic applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
82 | Gen_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for generic applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
83 | ScndPHdConst | This control mode operates the device with constant differential pressure. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
84 | ScndPHdVar | This control mode operates the device with a differential pressure which varies with the flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
85 | ScndFlow | This control mode operates the device with constant volume flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
86 | ScndSpd | This control mode operates the motor with constant speed. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
87 | HeatConcrete_PHd | This control mode operates the device with a differential pressure for concrete core activation heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
88 | HeatConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
89 | HeatConcrete_TDiff | This control mode operates the device with constant differential temperature for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
90 | HeatConcrete_Flow | This control mode operates the device with constant volume flow for heating applications with concrete core activation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
91 | HeatBottle_Flow | This control mode operates the device with constant volume flow for heating applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
92 | HeatMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
93 | HeatMan_Flow | This control mode operates the device with constant volume flow for heating applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
94 | HeatTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with storage tank.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
95 | HeatTank_Flow | This control mode operates the device with constant volume flow for heating applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
96 | HeatExchanger_Flow | This control mode operates the device with constant volume flow for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
97 | HeatSource_TDiff | This control mode operates the device with constant differential temperature for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
98 | HeatSource_Flow | This control mode operates the device with constant volume flow for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
99 | HeatDistrict_PHdConst | This control mode operates the device with a differential pressure for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
100 | HeatDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
101 | HeatDistrict_PHdExt | This control mode operates the device with constant differential pressure for district heating application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernwärme-Anwendungen. | Stratos GIGA 2.0; |
102 | CoolConcrete_PHd | This control mode operates the device with a differential pressure for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
103 | CoolConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
104 | CoolConcrete_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
105 | CoolConcrete_Flow | This control mode operates the device with constant volume flow for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
106 | CoolBottle_Flow | This control mode operates the device with constant volume flow for refrigeration applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
107 | CoolMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
108 | CoolMan_Flow | This control mode operates the device with constant volume flow for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
109 | CoolTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
110 | CoolTank_Flow | This control mode operates the device with constant volume flow for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
111 | CoolExchanger_Flow | This control mode operates the device with constant volume flow for refrigeration applications with heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
112 | CoolCondenser_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with recirculating cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
113 | CoolCondensor_Flow | This control mode operates the device with constant volume flow for refrigeration applications with recirculationg cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
114 | CoolDistrict_PHdConst | This control mode operates the device with a differential pressure for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
115 | CoolDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
116 | CoolDistrict_PHdExt | This control mode operates the device with constant differential pressure for district refrigeration application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernkühlungs-Anwendungen. | Stratos GIGA 2.0; |
117 | 108_RESERVED | reserved for future use reserviert | − |
118 | 109_RESERVED | reserved for future use reserviert | − |
139 | Gen_PVar | This control mode operates the device with a discharge pressure that varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigen Ausgangsdruck. | MVIE, …; |
140 | Gen_UsrDfd | This control mode operates the device with user configurable PID controller.Diese Steuerungsart betreibt das Gerät mit einem frei konfigurierbaren PID-Regler für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; IL_E, …; MVIE, …; |
Dies definiert einen alternativen Wert für das folgende Signal. Dieses Signal beinhaltet die Steuerungsart für das Gerät. Wird eine gewählte Steuerungsart nicht unterstützt, bleibt das Gerät bei der zuletzt eingestellten Steuerungsart.This defines an alternative value for the following signal. This signal represents the control mode for the device. In case a selected mode is not supported, the device will stay in the previously selected mode.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 414 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Pump on aux. | Dies definiert einen alternativen Wert für das folgende Signal. Dieses Signal repräsentiert den normalen Einschaltbefehl. Er wird umgesetzt, wenn keine Übersteuerungsfunktionen aktiv sind. | This defines an alternative value for the following signal. This signal represents the normal "ON" command. This signal is effektive, if no override functions are active. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies definiert einen alternativen Wert für das folgende Signal. Dieses Register ist ein zuätzlicher Steuereingang für das Gerät. Es kann ein- bzw. ausgeschaltet werden oder auch mit Minimal- oder Maximalwerten übersteuert werden.This defines an alternative value for the following signal. This register is an auxiliary control for the device. It can be switched on or off. furthermore, the on/off command can be overridden with min or max values.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 415 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | IF-Module | Signal source for setpoint: IF-ModuleSollwertquelle IF-Modul | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …; |
2 | 0…10 V | Signal source for setpoint: IN2 mode 0…10 VSollwertquelle: IN2 Modus 0…10 V | CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …; |
3 | 2…10 V | Signal source for setpoint: IN2 mode 2…10 VSollwertquelle: IN2 Modus 2…10 V | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
4 | 0…20 mA | Signal source for setpoint: IN2 mode 0…20 mASollwertquelle: IN2 Modus 0…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
5 | 4…20 mA | Signal source for setpoint: IN2 mode 4…20 mASollwertquelle: IN2 Modus 4…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
6 | Internal | Signal source for setpoint: internalSollwertquelle: Intern | Stratos MAXO; Stratos GIGA 2.0; |
7 | EXT 1 | Signal source for setpoint: EXT 1Sollwertquelle: EXT 1 | Stratos MAXO; Stratos GIGA 2.0; |
8 | EXT 2 | Signal source for setpoint: EXT 2Sollwertquelle: EXT 2 | Stratos MAXO; Stratos GIGA 2.0; |
9 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
Dies definiert einen alternativen Wert für das folgende Signal. Dieses Signal enthält die Sollwertquelle in der aktuellen Regelungsart. This defines an alternative value for the following signal. This signal represents the source for the setpoint for the current control function.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 416 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | norm | normal paremeter setParametersatz normal | CIF-/IF-Module internal; |
2 | aux | auxiliary parameter setParametersatz zusätzlich | CIF-/IF-Module internal; |
3 | preset | preset parameter set (startup/fallback)Parametersatz Preset (Voreinstellung / Fallback) | CIF-/IF-Module internal; |
5 | INVALID | value for parameter set invalidWert für Parametersatz ungültig | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Dieses Signal beinhaltet die Information über den Parametersatz zur Steuerung des Geräts: Der Parametersatz umfasst mindestens Sollwert, Regelungsart, Pumpe ein/aus und Sollwertquelle.This is the base signal. This signal contains information about the parameter set for device control. The parameter set constist of at least the duty point, the control mode, the on/off command and the signal source for the duty point.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 420 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | REAL |
unitEinheit | m³/h |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dies definiert den Maximalgrenze des folgenden Signals. Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This defines the maximum limit of the following signal. This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 422 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | REAL |
unitEinheit | m³/h |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dies definiert den Minimalgrenze des folgenden Signals. Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This defines the minimum limit of the following signal. This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 424 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | REAL |
unitEinheit | m³/h |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dies beinhaltet die untere Abschaltgrenze des Signals Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This incorporates the 'off' limit for the signal This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 426 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den Sollwert-Reduktionsfaktor für durchflussabhängige Regelungsfunktionen bei Null-DurchflußThis is the base signal. This signal represents the setpoint reduction factor for flow dependent control funtions at zero flow.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 427 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | UINT |
unitEinheit | m³/h |
scaleSkalierung | 0.1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den Nenn-Durchflusses, auf den sich der Sollwert für eine volumenstromabhängige Regelungsfunktion bezieht.This is the base signal. This signal represents the nominal flow where the setpoint of a flow variable control function refers to.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 847 |
scopeBereich | pump systemPumpensystem |
functionFunktion | input value Eingangswert |
data typeDatentyp | UINT |
unitEinheit | m³/h |
scaleSkalierung | 0.1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.02…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den kummulierten Durchfluss-Ersatzwert für die Pumpen, welche in einem Pumpenverbund permanent keine Durchflußinformation bereitstellen können.This is the base signal. This signal represents the accumulated flow replacement value for all pumps of a pump combination, which permanently cannot provide a flow information.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0;
addressAdresse | nameName |
---|---|
1 | Pressure |
2 | Flow (calculated) |
3 | Energy Consumption |
4 | power input |
5 | Operation Time |
6 | Electrical Current |
7 | Speed |
8 | temperature fluid @ device |
9 | Operating Hours DP |
10 | Control Function |
16 | Pump Module |
17 | Pump Type |
18 | Speed max-pres-value |
19 | Speed min-pres-value |
20 | Pressure Max Δp-c |
21 | Pressure Min Δp-c |
22 | Pressure Max Δp-v |
23 | Pressure Min Δp-v |
24 | Flow (calculated) max-pres-value |
25 | Flow (calculated) min-pres-value |
26 | Supported Errors |
27 | Supported Service Messages |
28 | power input max-pres-value |
35 | Service Message |
36 | Error Type |
37 | Error Message |
38 | Pump Status |
39 | State Diagnostics |
65 | Pressure |
66 | Flow (calculated) |
67 | Energy Consumption |
68 | power input |
69 | Operation Time |
70 | Electrical Current |
71 | Speed |
80 | Pump Module (Slave) |
81 | Pump Type (Slave) |
100 | Error Type (Slave) |
102 | Pump Status (Slave) |
200 | duty point (rel.) |
202 | duty point (rel.) maximum-output |
204 | duty point (rel.) minimum-output |
206 | duty point 100 % value |
208 | duty point (rel.) units |
210 | Setpoint Signal Source |
211 | parameter set selector |
222 | duty point (rel.) maximum-output |
224 | duty point (rel.) minimum-output |
226 | duty point 100 % value |
228 | duty point (rel.) units |
232 | duty point (rel.) aux. maximum-output |
234 | duty point (rel.) aux. minimum-output |
236 | duty point 100 % value aux. |
238 | duty point (rel.) aux. units |
242 | duty point (rel.) preset maximum-output |
244 | duty point (rel.) preset minimum-output |
246 | duty point 100 % value preset |
248 | duty point (rel.) preset units |
250 | duty point (rel.) |
252 | duty point (rel.) maximum-output |
254 | duty point (rel.) minimum-output |
256 | duty point 100 % value |
258 | duty point (rel.) units |
260 | Control Function |
261 | Pump Command |
262 | Setpoint Signal Source |
270 | Flow (calculated) limit. max |
272 | Flow (calculated) limit. min |
274 | Flow (calculated) limit. off |
280 | Flow zero setpoint red. factor |
281 | Flow nominal for Ctrl. Fun. |
300 | power heating |
302 | power refrigeration |
304 | Energy heat. rst.able |
306 | Energy heat. rst.able start-time |
308 | Energy refrig. rst.able |
310 | Energy refrig. rst.able start-time |
312 | Energy heating total |
314 | Energy refrigeration total |
316 | temperature fluid forward |
318 | temperature fluid return |
320 | Voltage Input |
324 | Analog In 1 Measured Val. |
326 | Analog In 2 Measured Val. |
328 | Analog In 1 Measured Val. units |
329 | Analog In 2 Measured Val. units |
330 | temperature reference T1 |
332 | temperature reference T2 |
334 | Analog In 3 Measured Val. |
336 | Analog In 4 Measured Val. |
338 | Analog In 3 Measured Val. units |
339 | Analog In 4 Measured Val. units |
400 | duty point (rel.) |
402 | Pump Command active |
403 | Pump Command out |
404 | Operation Status |
500 | Heartbeat Count |
502 | System Time |
504 | Bus Command Timer Time remain. |
700 | Application Version |
702 | Vendor ID |
704 | software build id |
740 | pump type CAN |
750 | pump type CAN |
850 | Flow replacement value |
901 | User Trouble Code |
940 | Warning/Error Message |
950 | Warning/Error Message |
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 1 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den Druck-Istwert an der Pumpe. Je nach Sensoranordnung ist dies ein Absolut- oder Differenzdruck oder auch ein Signal von einem abgesetzen Sensor. Einige Pumpentypen arbeiten sensorlos, dort ist es ein berechneter Wert.This is the base signal. This signal represents the current pressure at the pump system. Depending on the sensor arrangement, this value is an absolute or a differential pressure. It can also be a signal of a remote sensor. Some pump type operate without a pressure sensor. In this case, the value is calculated.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 2 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | m³/h |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 9998 |
error valueFehlerwert | 9999 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This is the base signal. This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 3 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | kWh |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Wert repräsentiert die bisher aufgenommene elektrische Energie (Energiezähler). Er dient zur Einschätzung des Verbrauchs.This is the base signal. This value represent the totally consumed electrical energy. This value is suitable for an energy performance evaluation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 4 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | W |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die aktuelle elektrische Eingangsleistung.This is the base signal. This signal represents the current electrical input power.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 5 |
scopeBereich | master pumpMaster-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | h |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Wert zeigt die gesamte Zeit während der das Gerät in Betrieb war (drehender Motor).This is the base signal. This value represents the total time where the device was running (motor turning).
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 6 |
scopeBereich | master pumpMaster-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | A |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den aktuellen elektrischen Eingangsstrom .This is the base signal. This signal represents the electrical input current.
Support reference: Wird unterstützt durch: Stratos; IL_E, … MVIE, …(0.55…7.5 kW);
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 7 |
scopeBereich | master pumpMaster-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | 1/min |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die Drehzahl der Pumpe.This is the base signal. This signal shows the rotational speed of the pump.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 8 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | K |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert liefert den Meßwert für die Medientemperatur. Dies kann auch ein Wert von einem abgesetzten Sensor sein.This is the base signal. This signal shows the measurement value of the fluid temperature sensor. It can also be a remote sensor signal.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 9 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | h |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Wert zeigt die gesamte Zeit während der das Gerät in Betrieb war (drehender Motor). Dieses Register liefert die Betriebszeit des Doppelpumpensystems.This is the base signal. This value represents the total time where the device was running (motor turning). This Input register returns the operating time of the double pump system.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 10 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | Gen_Spd | This control mode operates the device with constant speed.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
2 | CONST_FREQ | reservedreserviert | − |
3 | Gen_PHdConst | This control mode operates the device with constant differential pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
4 | Gen_PHdVar | This control mode operates the device with a differential pressure which varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; |
5 | Gen_PConst | This control mode operates the device with constant discharge pressure.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Ausgangsdruck. | MVIE, …; |
6 | TEMP_VARIABLE | This control mode operates the device with a differential pressure which varies with the fluid temperature.Diese Steuerungsart betreibt das Gerät mit mediumstemperaturabhängigem Differenzdruck (Δp-c=F(T)) . | CIF-/IF-Module internal; Stratos; |
6 | CONST_POWER | reservedreserviert | − |
7 | CONST_HEAD | reservedreserviert | − |
8 | CONST_FLOW | reservedreserviert | − |
9 | Gen_T | This control mode operates the device with constant temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
10 | Gen_TDiff | This control mode operates the device with constant differential temperature for generic application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
11 | CONST_LEV | reservedreserviert | − |
15 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
16 | HeatRadiator_PHd | This control mode operates the device with a differential pressure which varies with the flow for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
17 | HeatRadiator_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating radiator applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
18 | HeatRadiator_T | This control mode operates the device with constant temperature for heating radiator application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizkörperanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
19 | HeatFloor_PHd | This control mode operates the device with a differential pressure for floor heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
20 | HeatFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
21 | HeatFloor_T | This control mode operates the device with constant temperature for floor heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
22 | HeatCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
23 | HeatCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
24 | HeatCeiling_T | This control mode operates the device with constant temperature for ceiling heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenheizungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
25 | HeatFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
26 | HeatFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
27 | HeatFan_T | This control mode operates the device with constant temperature for fan coil heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
28 | HeatB._T | This control mode operates the device with constant temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
29 | HeatB._TDiff | This control mode operates the device with constant differential temperature for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
30 | HeatB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
31 | HeatE._T | This control mode operates the device with constant temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
32 | HeatE._TDiff | This control mode operates the device with constant differential temperature for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
33 | HeatE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
34 | Heat_PHdConst | This control mode operates the device with constant differential pressure for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
35 | Heat_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
36 | Heat_PHdExt | This control mode operates the device with constant differential pressure for heating applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
37 | Heat_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
38 | Heat_VolFlow | This control mode operates the device with constant volume flow for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
39 | Heat_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
40 | Heat_T | This control mode operates the device with constant temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
41 | Heat_TDiff | This control mode operates the device with constant differential temperature for heating application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
42 | Heat_Spd | This control mode operates the device with constant speed for heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Heizungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
43 | CoolCeiling_PHd | This control mode operates the device with constant differential pressure for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
44 | CoolCeiling_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for ceiling refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
45 | CoolCeiling_T | This control mode operates the device with constant temperature for ceiling refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Deckenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
46 | CoolFloor_PHd | This control mode operates the device with constant differential pressure for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
47 | CoolFloor_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
48 | CoolFloor_T | This control mode operates the device with constant temperature mode for floor refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Fußbodenkühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
49 | CoolFan_PHd | This control mode operates the device with a differential pressure which varies with the flow for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstronmabhängigem Differenzdruck für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
50 | CoolFan_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for fan coil refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
51 | CoolFan_T | This control mode operates the device with constant temperature mode for fan coil refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit Gebläsekonvektor. | Stratos MAXO; Stratos GIGA 2.0; |
52 | CoolB._T | This control mode operates the device with constant temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
53 | CoolB._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
54 | CoolB._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with hydraulic separator.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit hydraulischer Weiche. | Stratos MAXO; Stratos GIGA 2.0; |
55 | CoolE._T | This control mode operates the device with constant temperature mode for refrigeration application with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühlungs-Anwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
56 | CoolE._TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Wärmetauscher. | Stratos MAXO; Stratos GIGA 2.0; |
57 | CoolE._Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with heat exhanger.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Wärmetauscher | Stratos MAXO; Stratos GIGA 2.0; |
58 | Cool_PHdConst | This control mode operates the device with constant differential pressure for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
59 | Cool_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
60 | Cool_PHdExt | This control mode operates the device with constant differential pressure for refrigeration application with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Kühlungs-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
61 | Cool_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
62 | Cool_VolFlow | This control mode operates the device with constant volume flow for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
63 | Cool_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen | Stratos MAXO; Stratos GIGA 2.0; |
64 | Cool_T | This control mode operates the device with constant temperature mode for refrigeration application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Kühl-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
65 | Cool_TDiff | This control mode operates the device with constant differential temperature for cooling application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
66 | Cool_Spd | This control mode operates the motor with constant speed for refrigeration applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Kühlungsanwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
67 | San_Circ._T | This control mode operates the device with constant temperature for sanitary hot water circulation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Zirkulations-Anwendungen. | Stratos MAXO; |
68 | SanW.Heat._TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application with heat exchanger in the storage tank.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen mit Wärmetauscher im Warmwasserspeicher | Stratos MAXO; Stratos GIGA 2.0; |
69 | SanL.S._T | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
70 | SanL.S._Acc.Flow | reservedreserviert | Stratos MAXO; Stratos GIGA 2.0; |
71 | San_PHdConst | This control mode operates the device with constant differential pressure for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
72 | San_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Trink-Warmwasser-Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
73 | San_PHdExternal | This control mode operates the device with constant differential pressure for sanitary hot water applications with external differential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
74 | San_VolFlow | This control mode operates the device with constant volume flow for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
75 | San_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Trink-Warmwasser-Anwendungen | Stratos MAXO; Stratos GIGA 2.0; |
76 | San_T | This control mode operates the device with constant temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Temperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
77 | San_TDiff | This control mode operates the device with constant differential temperature for sanitary hot water application.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
78 | San_Spd | This control mode operates the motor with constant speed for sanitary hot water applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl für Trink-Warmwasser Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
79 | Gen_PHdExt | This control mode operates the device with constant differential pressure for generic applications with external diffential pressure sensor.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
80 | Gen_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for generic applications.Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
81 | Gen_VolFlow | This control mode operates the device with constant volume flow for generic applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
82 | Gen_Acc.Flow | This control mode operates the device with a setpoint depending on the volume flow of other pumps for generic applications.Diese Steuerungsart betreibt das Gerät mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; |
83 | ScndPHdConst | This control mode operates the device with constant differential pressure. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
84 | ScndPHdVar | This control mode operates the device with a differential pressure which varies with the flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
85 | ScndFlow | This control mode operates the device with constant volume flow. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
86 | ScndSpd | This control mode operates the motor with constant speed. A special parameter set which is stored in the device is used.Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Drehzahl. Hierfür wird ein separater Parametersatz verwendet, der in der Pumpe gespeichert ist. | Stratos MAXO; Stratos GIGA 2.0; |
87 | HeatConcrete_PHd | This control mode operates the device with a differential pressure for concrete core activation heating applications.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
88 | HeatConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
89 | HeatConcrete_TDiff | This control mode operates the device with constant differential temperature for heating applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
90 | HeatConcrete_Flow | This control mode operates the device with constant volume flow for heating applications with concrete core activation.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
91 | HeatBottle_Flow | This control mode operates the device with constant volume flow for heating applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
92 | HeatMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
93 | HeatMan_Flow | This control mode operates the device with constant volume flow for heating applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
94 | HeatTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for heating applications with storage tank.Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
95 | HeatTank_Flow | This control mode operates the device with constant volume flow for heating applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
96 | HeatExchanger_Flow | This control mode operates the device with constant volume flow for heating applications with heat exchanger.Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
97 | HeatSource_TDiff | This control mode operates the device with constant differential temperature for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
98 | HeatSource_Flow | This control mode operates the device with constant volume flow for heating applications with ground coupled heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Heizungsanwendungen mit Erdwärmesonde. | Stratos GIGA 2.0; |
99 | HeatDistrict_PHdConst | This control mode operates the device with a differential pressure for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
100 | HeatDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district heating applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernheizungsanwendungen. | Stratos GIGA 2.0; |
101 | HeatDistrict_PHdExt | This control mode operates the device with constant differential pressure for district heating application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernwärme-Anwendungen. | Stratos GIGA 2.0; |
102 | CoolConcrete_PHd | This control mode operates the device with a differential pressure for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Heizungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
103 | CoolConcrete_DA | This control mode operates the device with automatic setpoint adjustement (dynamic adapt) for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit automatischer Sollwertanpassung (Dynamic Adapt) für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
104 | CoolConcrete_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
105 | CoolConcrete_Flow | This control mode operates the device with constant volume flow for refrigeration applications with concrete core activation. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Betonkernaktivierung. | Stratos GIGA 2.0; |
106 | CoolBottle_Flow | This control mode operates the device with constant volume flow for refrigeration applications with hydraulic separator. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
107 | CoolMan_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
108 | CoolMan_Flow | This control mode operates the device with constant volume flow for refrigeration applications with manifold. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Verteilerbalken. | Stratos GIGA 2.0; |
109 | CoolTank_MFA | This control mode operates the device with a setpoint depending on the volume flow of other pumps for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät in mit einem vom Durchfluß anderer Pumpen abhängigen Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
110 | CoolTank_Flow | This control mode operates the device with constant volume flow for refrigeration applications with storage tank. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Pufferspeicher. | Stratos GIGA 2.0; |
111 | CoolExchanger_Flow | This control mode operates the device with constant volume flow for refrigeration applications with heat exchanger. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Wärmetauscher. | Stratos GIGA 2.0; |
112 | CoolCondenser_TDiff | This control mode operates the device with constant differential temperature for refrigeration applications with recirculating cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängiger Differenztemperatur für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
113 | CoolCondensor_Flow | This control mode operates the device with constant volume flow for refrigeration applications with recirculationg cooler. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Durchfluß für Kühlungsanwendungen mit Rückkühler. | Stratos GIGA 2.0; |
114 | CoolDistrict_PHdConst | This control mode operates the device with a differential pressure for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
115 | CoolDistrict_PHdVar | This control mode operates the device with a differential pressure which varies with the flow for district refrigeration applications. Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigem Differenzdruck für Fernkühlungsanwendungen. | Stratos GIGA 2.0; |
116 | CoolDistrict_PHdExt | This control mode operates the device with constant differential pressure for district refrigeration application with external differential pressure sensor. Diese Steuerungsart betreibt das Gerät mit sollwertabhängigem Differenzdruck und externem Istwertgeber für Fernkühlungs-Anwendungen. | Stratos GIGA 2.0; |
117 | 108_RESERVED | reserved for future use reserviert | − |
118 | 109_RESERVED | reserved for future use reserviert | − |
139 | Gen_PVar | This control mode operates the device with a discharge pressure that varies with the flow.Diese Steuerungsart betreibt das Gerät mit sollwert- und volumenstromabhängigen Ausgangsdruck. | MVIE, …; |
140 | Gen_UsrDfd | This control mode operates the device with user configurable PID controller.Diese Steuerungsart betreibt das Gerät mit einem frei konfigurierbaren PID-Regler für generische Anwendungen. | Stratos MAXO; Stratos GIGA 2.0; IL_E, …; MVIE, …; |
Dieses Signal ist das Grundsignal. Dieses Signal beinhaltet die Steuerungsart für das Gerät. Wird eine gewählte Steuerungsart nicht unterstützt, bleibt das Gerät bei der zuletzt eingestellten Steuerungsart.This is the base signal. This signal represents the control mode for the device. In case a selected mode is not supported, the device will stay in the previously selected mode.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 16 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | TRUE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '1' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer gesetzt sein. | This is the base signal. This signal represens a static '1' bit, typically for compatibility purpose. For write acces, this bit shall always be '1'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert die Information über die Art des Pumpen-Steuermoduls.This is the base signal. This register returns if the pump module is controlled by a frequency converter or not.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 17 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
254 | EXTENDED | This value is valid, but not covered by this enumeration.Dieser Wert ist gültig, aber nicht in dieser Aufzählung enthalten. | CIF-/IF-Module internal; |
255 | INVALID | This value is invaid (error value).Dieser Wert ist ungültig (Fehlerwert) | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Dieses Signal zeigt den Pumpentyp in der PLR-Notation. Dieser Datenpunkt ist aus Kompatibilitätsgründen vorhanden. Ist für die Pumpe kein PLR-Typ ermittelbar, wird der Wert EXTENDED zurückgegeben.This is the base signal. This signal shows the pump type in PLR notation. This signal is presented for compatibility reason. If this pump has no PLR pump type, the value EXTENDED will be returned.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 18 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
unitEinheit | 1/min |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die Drehzahl der Pumpe.This is the base signal. This signal shows the rotational speed of the pump.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 19 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
unitEinheit | 1/min |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die Drehzahl der Pumpe.This is the base signal. This signal shows the rotational speed of the pump.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 20 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert den maximal möglichen Soll-Druck in der Regelart Δ p-c. Es kann benutzt werden um einen in % skalierten Sollwert oder Istwert auf die physikalische Größe zu skalieren. Bei Multistage Pumpen ist dies der Meßbereich des Sensors, nicht der Maximaldruck der Pumpe.This is the base signal. This signal shows the maximum possible pressure setpointfor the operation mode Δ p-c. It can be used to scale a setpoint in percent back to the physical unit. For multistage pumps, this value is not the maximum head of the pump, but the measurement range of the sensor.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 21 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert den minimal möglichen Druck-Sollwert in der Regelart Δ p-c.This is the base signal. This signal shows the minimum possible pressure setpoint in the operation mode Δ p-c.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 22 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert den maximal möglichen Soll-Druck in der Regelart Δ p-v. Es kann benutzt werden um einen in % skalierten Sollwert oder Istwert auf die physikalische Größe zu skalieren. Bei Multistage Pumpen ist dies der Meßbereich des Sensors, nicht der Maximaldruck der Pumpe.This is the base signal. This signal shows the maximum possible pressure setpoint for the operation mode Δ p-v. It can be used to scale a setpoint in percent back to the physical unit. For multistage pumps, this value is not the maximum head of the pump, but the measurement range of the sensor.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 23 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert den minimal möglichen Druck-Sollwert in der Regelart Δ p-v.This is the base signal. This signal shows the minimum possible pressure setpoint in the operation mode Δ p-v.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 24 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | m³/h |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This is the base signal. This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 25 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | m³/h |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This is the base signal. This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 26 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
range lowBereich min. | 0 |
range highBereich max. | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert die unterstützten Fehlermeldungen als Bitset. Diese können aus dem Input Register 37 gelesen werden. Hinweis: dieses Register ist auf Kompatibilitätsgründen vorhanden und wird in einer der zukünftigen Softwareversionen entfallen. Daher zeigt es einen statischen Wert von 0xFFFF, so als ob alle Fehler unterstützt würden.This is the base signal. This register returns the supported errors that can be read in Input Register 37. Notice: This register is available for compatibility reasons and will be removed in future software versions. Therefore it indicates the support of all errors (value 0xFFFF).
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 27 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
range lowBereich min. | 0 |
range highBereich max. | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert die unterstützten Service-Meldung, die im Input Register 35 (Service Message) gelesen werden können. Hinweis: dieses Register ist aus Kompatibilitätsgründen vorhanden und wird in einer der zukünftigen Softwareversionen entfallen. Daher zeigt es einen statischen Wert von 0xFFFF, so als ob alle Service-Meldungen unterstützt würden.This is the base signal. This Input register returns the supported service messages that can be read in the Input register address 35 (Service Message). Notice: This register is available for compatibility reasons and will be removed in future software versions. Therefore it indicates the support of all service messages (value 0xFFFF).
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 28 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | W |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die aktuelle elektrische Eingangsleistung.This is the base signal. This signal represents the current electrical input power.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 35 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Service Required | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass eine Service-Aktion erforderlich ist. Dieses Signal bedeutet keine akute Funktionseinschränkung. | This is the base signal. This signal shows a required service action for the device. It does not mean any current insufficency for the operation. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
2 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Diese Register liefert die Information über die aktuell nötigen Service-Aktionen.This is the base signal. This Input register returns the current service actions needed.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 36 |
scopeBereich | master pumpMaster-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Status Module error | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Fehler im Elektronikmodul an. | This is the base signal. This signal shows an error inside the electronic module. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | Status Motor error | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Motorfehler an. | This is the base signal. This signal is set, if the motor has a failure. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | Error Present | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Fehler der Pumpe an und bedeutet, dass der Motor nicht dreht. Ein automatischer Wiederanlaufversuch wird erfolgen. | This is the base signal. This signal shows an error of the pump. It means that the motor is currently stopped. A start retry will be performed. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
4 | Status supply voltage error | Dieses Signal ist das Grundsignal. Dieses Signal wird gesetzt, wenn die Eingangsspannung nicht den Anforderungen entspricht. | This is the base signal. This signal is set if the supply voltage is not adequate for operation. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Diese Register liefert eine Information über den Fehlerstatus der Pumpe. Hinweis: Dieses Register ist aus Kompatibilitätsgründen verfügbar. Für Neuentwicklungen verwenden Sie bitte die Register 940/950. Dieses liefert den WILO Fehlercode.This is the base signal. This Input register returns the pump error. If one bit is active an error is present. A possible list of errors is located in the pump manual.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 37 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Status Undervoltage | Dieses Signal ist das Grundsignal. Dieses Signal zeigt den Zustand "Unterspannung". Es bedeutet, dass die Versorgungsspannung für einen Betrieb nicht ausreichend ist | This is the base signal. This signal shows that the supply voltage for the device is insufficient. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | Status Overvoltage | Dieses Signal ist das Grundsignal. Dieses Signal zeigt den Zustand "Überspannung". Es bedeutet, dass die Versorgungsspannung für einen Betrieb zu hoch ist. | This is the base signal. This signal shows that the supply voltage for the device is too high. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
2 | Status Phase fault | Dieses Signal ist das Grundsignal. Dieses Signal zeigt den Zustand "Phasenfehler". Es bedeutet, dass vom versorgenden Netzt mindestens eine Phase eine ungenügende Versorgungsqualität aufweist. | This is the base signal. This signal shows that the supply has a phase fault. At least the supply via one phase is insufficient. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | Status Idle running | Dieses Signal ist das Grundsignal. Dieses Signal zeigt den Zustand Leerlauf der Pumpe. Es bedeutet, dass die bei dieser Drehzahl erwartete Mindestlast (z.B. durch Luft im System) nicht erreicht wird. | This is the base signal. This signal shows an idling state of the pump. The minimum load for the current speed is not reached (due to e.g. air in in the system). | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
8 | Status Motor overheated | Dieses Signal ist das Grundsignal. Dieses Signal zeigt eine zu hohe Motortemperatur an. | This is the base signal. This signal is set, if the motor tempaerature is too high. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
9 | Status Motor error | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Motorfehler an. | This is the base signal. This signal is set, if the motor has a failure. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
10 | Status Pump blocked | Dieses Signal ist das Grundsignal. Dieses Signal zeigt eine Blockierung der Motorwelle (z.B. durch Verstopfung des Laufrades oder Korrosion) an. | This is the base signal. This signal is set, if the shaft of the motor is blocked. This may occur due to a blocked impeller or corrosion. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
11 | Status Module overheated | Dieses Signal ist das Grundsignal. Dieses Signal zeigt eine zu hohe Temperatur des Elektronikmoduls an. | This is the base signal. This signal is set, if the temperature of the electronic module is too high. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
12 | Status Module warning | Dieses Signal ist das Grundsignal. Dieses Signal zeigt eine mögliche Unterversorgung an, die im Elektronikmodul erkannt wúrde. | This is the base signal. This signal is set as a warning from the eletronic module that perfomance may become insufficient. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
13 | Status Module error | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Fehler im Elektronikmodul an. | This is the base signal. This signal shows an error inside the electronic module. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
14 | Status sensor malfunction | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Fehler in einem internen oder externen Sensor an. | This is the base signal. This signal shows an error of an internal or external sensor. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert den Pumpenfehler als Bitset. Gemeldet werden nur Fehler (die auch eine Aktivierung des SSM bewirken). Hinweis: Dieses Register ist aus Kompatibilitätsgründen verfügbar. Für Neuentwicklungen verwenden Sie bitte die Register 940/950. Diese liefern den WILO Fehlercode.This is the base signal. This Input register returns the error as a bitset . No warnings are transmitted over the bus, only Errors (when the SSM relay becomes active in the Pump). Notice: This register is available for compatibility reasons and will be removed in future software versions, for new projects please use register 940/950. They represent the Wilo error code.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 38 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Pump on | Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den normalen Einschaltbefehl. Er wird umgesetzt, wenn keine Übersteuerungsfunktionen aktiv sind. | This is the base signal. This signal represents the normal "ON" command. This signal is effektive, if no override functions are active. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
2 | Status setpoint difference | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass der eingestellte Sollwert nicht erreicht wurde. Ursachen können eine zu geringe ausgewählte Pumpenleistung bzw. eine zu geringe Sollwerteinstellung sein. | This is the base signal. This signal shows that the setpoint is not reached. Possible causes are an insufficient pump size or a setpoint which is lower than the minimal setpoint. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | Override off | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "OFF" Befehl. | This is the base signal. This signal overrides the pump (system) command with "OFF" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
4 | Pump configuration double pump | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass es sich bei dem angeschlossenen Gerät um eine Doppelpumpe handelt. | This is the base signal. This signal shows that the pump system is a double pump. | GLANDLESS, GLANDED_SINGLE, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
5 | Status local operation active | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass die Steuerung über diesen Kanal durch eine lokale Aktion am Gerät derzeit blockiert ist. | This is the base signal. This signal shows that the control via this communication channel is overidden by a local action at the device. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
6 | Status Q/H values invalid | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass die Werte für Durchfluß (Q) und/oder (Differenz-)Druck ungültig sind. | This is the base signal. This signal shows that the values for flow (Q) and/or (differential) pressure are invalid. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
7 | Override min | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "MIN" Befehl. | This is the base signal. This signal overrides the pump (system) command with "MIN" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
8 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (5.00…99.99), CIF-Module Modbus RTU (5.00…99.99) |
9 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (5.00…99.99), CIF-Module Modbus RTU (5.00…99.99) |
10 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (5.00…99.99), CIF-Module Modbus RTU (5.00…99.99) |
11 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (5.00…99.99), CIF-Module Modbus RTU (5.00…99.99) |
12 | Status External setpoint active | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass der Sollwert nicht über diesen Kommunikationskanal vorgegeben wird | This is the base signal. This signal shows that the setpoint is not provided by this communication channel. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (5.00…99.99), CIF-Module Modbus RTU (5.00…99.99) |
13 | Wink Service | Dieses Signal ist das Grundsignal. Wenn der Menüpunkt "ID" im Gerätemenü aktiviert wurde, wird dieses Signal für einige Sekunden gesetzt. | This is the base signal. If the menuitem "ID" in the device menu is activated, this signal is activated for a few seconds. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
14 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (5.00…99.99), CIF-Module Modbus RTU (5.00…99.99) |
15 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | (…) |
Dieses Signal ist das Grundsignal. Dieses Register liefert den aktuellen Pumpenstatus. Es liefert Detailinformationen über den Pumpencontroller.This is the base signal. This Input register returns the current pump status. It contains detailed information about the controller.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 39 |
scopeBereich | pump systemPumpensystem |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Error Present | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Fehler der Pumpe an und bedeutet, dass der Motor nicht dreht. Ein automatischer Wiederanlaufversuch wird erfolgen. | This is the base signal. This signal shows an error of the pump. It means that the motor is currently stopped. A start retry will be performed. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | Status supply voltage error | Dieses Signal ist das Grundsignal. Dieses Signal wird gesetzt, wenn die Eingangsspannung nicht den Anforderungen entspricht. | This is the base signal. This signal is set if the supply voltage is not adequate for operation. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | Status lower regulation limit | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass sich der Drehzahl-Stellausgang zur Pumpe an der unteren Gerenze befindet. Die Pumpe / das Pumpensystem kann dem Stellsignal in diese Richtung nicht mehr folgen. | This is the base signal. This signal shows that the control output for the pump speed is at it´s low limit. The pump (system) cannot follow the control signal in this direction. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
4 | Status high regulation limit | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass sich der Drehzahl-Stellausgang zur Pumpe an der oberen Gerenze befindet. Die Pumpe / das Pumpensystem kann dem Stellsignal in diese Richtung nicht mehr folgen. | This is the base signal. This signal shows that the control output for the pump speed is as it´s high limit. The pump (system) cannot follow the control signal in this direction. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
6 | Status setpoint out of range | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass sich der eingestellte Sollwert außerhalb des möglichen Bereichs befindet. Die Pumpe wird den gewünschten Sollwert nicht erreichen. | This is the base signal. This signal shows that the setpoint is out of the possible range. The pump (system) will not perform according the setpoint. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
8 | Status local operation active | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass die Steuerung über diesen Kanal durch eine lokale Aktion am Gerät derzeit blockiert ist. | This is the base signal. This signal shows that the control via this communication channel is overidden by a local action at the device. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
10 | Pump on | Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den normalen Einschaltbefehl. Er wird umgesetzt, wenn keine Übersteuerungsfunktionen aktiv sind. | This is the base signal. This signal represents the normal "ON" command. This signal is effektive, if no override functions are active. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Input Register liefert einige Statusinformationen über die Pumpe.This is the base signal. This Input register returns some status information about the pump.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 65 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | cm H₂O |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den Druck-Istwert an der Pumpe. Je nach Sensoranordnung ist dies ein Absolut- oder Differenzdruck oder auch ein Signal von einem abgesetzen Sensor. Einige Pumpentypen arbeiten sensorlos, dort ist es ein berechneter Wert.This is the base signal. This signal represents the current pressure at the pump system. Depending on the sensor arrangement, this value is an absolute or a differential pressure. It can also be a signal of a remote sensor. Some pump type operate without a pressure sensor. In this case, the value is calculated.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 66 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | m³/h |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den (berechneten) Durchfluss. Bei berechneten Werten sollte dieser Wert nicht für geschlossene Regelkreise verwendet werden, da die Genauigkeit und Verfügbarkeit nicht in allen Betriebspunkten gewährleistet werden kann.This is the base signal. This signal represents the (calculated) flow. Calculated values are not suitable for closed loop control applications due to restricted availibility and precision over the range of operation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 67 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | kWh |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Wert repräsentiert die bisher aufgenommene elektrische Energie (Energiezähler). Er dient zur Einschätzung des Verbrauchs.This is the base signal. This value represent the totally consumed electrical energy. This value is suitable for an energy performance evaluation.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 68 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | W |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die aktuelle elektrische Eingangsleistung.This is the base signal. This signal represents the current electrical input power.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 69 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | h |
scaleSkalierung | 10 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieser Wert zeigt die gesamte Zeit während der das Gerät in Betrieb war (drehender Motor).This is the base signal. This value represents the total time where the device was running (motor turning).
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 70 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | A |
scaleSkalierung | 0.1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den aktuellen elektrischen Eingangsstrom .This is the base signal. This signal represents the electrical input current.
Support reference: Wird unterstützt durch: Stratos; IL_E, … MVIE, …(0.55…7.5 kW);
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 71 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | UINT |
unitEinheit | 1/min |
scaleSkalierung | 1 |
range lowBereich min. | 0 |
range highBereich max. | 65534 |
error valueFehlerwert | 65535 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert die Drehzahl der Pumpe.This is the base signal. This signal shows the rotational speed of the pump.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 80 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | TRUE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '1' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer gesetzt sein. | This is the base signal. This signal represens a static '1' bit, typically for compatibility purpose. For write acces, this bit shall always be '1'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert den Modultyp des Slaves in einer Doppelpumpe.This is the base signal. This Input register returns the module type of the Slave in a double pump.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 81 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
254 | EXTENDED | This value is valid, but not covered by this enumeration.Dieser Wert ist gültig, aber nicht in dieser Aufzählung enthalten. | CIF-/IF-Module internal; |
255 | INVALID | This value is invaid (error value).Dieser Wert ist ungültig (Fehlerwert) | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Dieses Signal zeigt den Pumpentyp in der PLR-Notation. Dieser Datenpunkt ist aus Kompatibilitätsgründen vorhanden. Ist für die Pumpe kein PLR-Typ ermittelbar, wird der Wert EXTENDED zurückgegeben.This is the base signal. This signal shows the pump type in PLR notation. This signal is presented for compatibility reason. If this pump has no PLR pump type, the value EXTENDED will be returned.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 100 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Status Module error | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Fehler im Elektronikmodul an. | This is the base signal. This signal shows an error inside the electronic module. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | Status Motor error | Dieses Signal ist das Grundsignal. Dieses Signal zeigt einen Motorfehler an. | This is the base signal. This signal is set, if the motor has a failure. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | Status supply voltage error | Dieses Signal ist das Grundsignal. Dieses Signal wird gesetzt, wenn die Eingangsspannung nicht den Anforderungen entspricht. | This is the base signal. This signal is set if the supply voltage is not adequate for operation. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
4 | Status supply voltage error | Dieses Signal ist das Grundsignal. Dieses Signal wird gesetzt, wenn die Eingangsspannung nicht den Anforderungen entspricht. | This is the base signal. This signal is set if the supply voltage is not adequate for operation. | PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert den Fehlertyp der Slave-Pumpe in einem DoppelpumpensystemThis is the base signal. This Input register returns the error type of the Slave in a double pump.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 102 |
scopeBereich | slave pumpSlave-Pumpe |
functionFunktion | output valueAusgangswert |
data typeDatentyp | WORD |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
bit | Name | Beschreibung | description | support | version |
---|---|---|---|---|---|
0 | Pump on | Dieses Signal ist das Grundsignal. Dieses Signal repräsentiert den normalen Einschaltbefehl. Er wird umgesetzt, wenn keine Übersteuerungsfunktionen aktiv sind. | This is the base signal. This signal represents the normal "ON" command. This signal is effektive, if no override functions are active. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
1 | FALSE | Dieses Signal ist das Grundsignal. Dieses Signal entspricht einem konstanten '0' Bit, typischerweise für Kompatibibitätszwecke. Für Schreibzugriff muss dieses immer zurückgesetzt sein. | This is the base signal. This signal represens a static '0' bit, typically for compatibility purpose. For write acces, this bit shall always be '0'. | PLC_INT | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
2 | Status setpoint difference | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass der eingestellte Sollwert nicht erreicht wurde. Ursachen können eine zu geringe ausgewählte Pumpenleistung bzw. eine zu geringe Sollwerteinstellung sein. | This is the base signal. This signal shows that the setpoint is not reached. Possible causes are an insufficient pump size or a setpoint which is lower than the minimal setpoint. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
3 | Override off | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "OFF" Befehl. | This is the base signal. This signal overrides the pump (system) command with "OFF" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
4 | Pump configuration double pump | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass es sich bei dem angeschlossenen Gerät um eine Doppelpumpe handelt. | This is the base signal. This signal shows that the pump system is a double pump. | GLANDLESS, GLANDED_SINGLE, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
5 | Status local operation active | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass die Steuerung über diesen Kanal durch eine lokale Aktion am Gerät derzeit blockiert ist. | This is the base signal. This signal shows that the control via this communication channel is overidden by a local action at the device. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
6 | Status Q/H values invalid | Dieses Signal ist das Grundsignal. Dieses Signal zeigt an, dass die Werte für Durchfluß (Q) und/oder (Differenz-)Druck ungültig sind. | This is the base signal. This signal shows that the values for flow (Q) and/or (differential) pressure are invalid. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, PLC_MAP | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
7 | Override min | Dieses Signal ist das Grundsignal. Dieses Signal übersteuert den Einschaltbefehl für die Pumpe (oder das Pumpensystem) mit einem "MIN" Befehl. | This is the base signal. This signal overrides the pump (system) command with "MIN" command. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
13 | Wink Service | Dieses Signal ist das Grundsignal. Wenn der Menüpunkt "ID" im Gerätemenü aktiviert wurde, wird dieses Signal für einige Sekunden gesetzt. | This is the base signal. If the menuitem "ID" in the device menu is activated, this signal is activated for a few seconds. | GLANDLESS, GLANDED_SINGLE, GLANDED_MULTI, STRATOS_MAXO, BLUE_OCEAN | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (1.00…99.99), IF-Module Modbus Stratos (1.13…99.99), IF-Module Modbus (1.13…99.99) |
Dieses Signal ist das Grundsignal. Dieses Register liefert den Pumpenstatus des Slaves in einem Doppelpumpensystem.This is the base signal. This Input register returns the pump status of the Slave in a double pump.
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 200 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 202 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 204 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 206 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | REAL |
unitEinheit | - |
scaleSkalierung | 1 |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert den 100 % Bezugswert für den Sollwert in der aktuellen Regelungsart.This is the base signal. This signal represent the 100 % reference value for the duty point in the current control function.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 208 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | UINT |
Module versionsModul-Versionen | Yonos MULTI CP Modbus (1.00…99.99), CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | square-feetsquare-feet | CIF-/IF-Module mapped; | |
2 | milliamperesmilliamperes | CIF-/IF-Module mapped; | |
3 | A | amperesamperes | CIF-/IF-Module mapped; |
4 | ohmsohms | CIF-/IF-Module mapped; | |
5 | V | voltsvolts | CIF-/IF-Module mapped; |
6 | kilovoltskilovolts | CIF-/IF-Module mapped; | |
7 | megavoltsmegavolts | CIF-/IF-Module mapped; | |
8 | volt-amperesvolt-amperes | CIF-/IF-Module mapped; | |
9 | kilovolt-ampereskilovolt-amperes | CIF-/IF-Module mapped; | |
10 | megavolt-amperesmegavolt-amperes | CIF-/IF-Module mapped; | |
11 | volt-amperes-reactivevolt-amperes-reactive | CIF-/IF-Module mapped; | |
12 | kilovolt-amperes-reactivekilovolt-amperes-reactive | CIF-/IF-Module mapped; | |
13 | megavolt-amperes-reactivemegavolt-amperes-reactive | CIF-/IF-Module mapped; | |
14 | degrees-phasedegrees-phase | CIF-/IF-Module mapped; | |
15 | power-factorpower-factor | CIF-/IF-Module mapped; | |
16 | joulesjoules | CIF-/IF-Module mapped; | |
17 | kilojouleskilojoules | CIF-/IF-Module mapped; | |
18 | watt-hourswatt-hours | CIF-/IF-Module mapped; | |
19 | kWh | kilowatt-hourskilowatt-hours | CIF-/IF-Module mapped; |
20 | btusbtus | CIF-/IF-Module mapped; | |
21 | thermstherms | CIF-/IF-Module mapped; | |
22 | ton-hourston-hours | CIF-/IF-Module mapped; | |
23 | joules-per-kilogram-dry-airjoules-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
24 | btus-per-pound-dry-airbtus-per-pound-dry-air | CIF-/IF-Module mapped; | |
25 | cycles-per-hourcycles-per-hour | CIF-/IF-Module mapped; | |
26 | cycles-per-minutecycles-per-minute | CIF-/IF-Module mapped; | |
27 | hertzhertz | CIF-/IF-Module mapped; | |
28 | grams-of-water-per-kilogram-dry-airgrams-of-water-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
29 | percent-relative-humiditypercent-relative-humidity | CIF-/IF-Module mapped; | |
30 | millimetersmillimeters | CIF-/IF-Module mapped; | |
31 | metersmeters | CIF-/IF-Module mapped; | |
32 | inchesinches | CIF-/IF-Module mapped; | |
33 | feetfeet | CIF-/IF-Module mapped; | |
34 | watts-per-square-footwatts-per-square-foot | CIF-/IF-Module mapped; | |
35 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
36 | lumenslumens | CIF-/IF-Module mapped; | |
37 | luxesluxes | CIF-/IF-Module mapped; | |
38 | foot-candlesfoot-candles | CIF-/IF-Module mapped; | |
39 | kilogramskilograms | CIF-/IF-Module mapped; | |
40 | pounds-masspounds-mass | CIF-/IF-Module mapped; | |
41 | tonstons | CIF-/IF-Module mapped; | |
42 | kilograms-per-secondkilograms-per-second | CIF-/IF-Module mapped; | |
43 | kilograms-per-minutekilograms-per-minute | CIF-/IF-Module mapped; | |
44 | kilograms-per-hourkilograms-per-hour | CIF-/IF-Module mapped; | |
45 | pounds-mass-per-minutepounds-mass-per-minute | CIF-/IF-Module mapped; | |
46 | pounds-mass-per-hourpounds-mass-per-hour | CIF-/IF-Module mapped; | |
47 | W | wattswatts | CIF-/IF-Module mapped; |
48 | kilowattskilowatts | CIF-/IF-Module mapped; | |
49 | megawattsmegawatts | CIF-/IF-Module mapped; | |
50 | btus-per-hourbtus-per-hour | CIF-/IF-Module mapped; | |
51 | horsepowerhorsepower | CIF-/IF-Module mapped; | |
52 | tons-refrigerationtons-refrigeration | CIF-/IF-Module mapped; | |
53 | pascalspascals | CIF-/IF-Module mapped; | |
54 | kilopascalskilopascals | CIF-/IF-Module mapped; | |
55 | bar | barsbars | CIF-/IF-Module mapped; |
56 | pounds-force-per-square-inchpounds-force-per-square-inch | CIF-/IF-Module mapped; | |
57 | centimeters-of-watercentimeters-of-water | CIF-/IF-Module mapped; | |
58 | inches-of-waterinches-of-water | CIF-/IF-Module mapped; | |
59 | millimeters-of-mercurymillimeters-of-mercury | CIF-/IF-Module mapped; | |
60 | centimeters-of-mercurycentimeters-of-mercury | CIF-/IF-Module mapped; | |
61 | inches-of-mercuryinches-of-mercury | CIF-/IF-Module mapped; | |
62 | Cel | degrees-Celsiusdegrees-Celsius | CIF-/IF-Module mapped; |
63 | K | degrees-Kelvindegrees-Kelvin | CIF-/IF-Module mapped; |
64 | degrees-Fahrenheitdegrees-Fahrenheit | CIF-/IF-Module mapped; | |
65 | degree-days-Celsiusdegree-days-Celsius | CIF-/IF-Module mapped; | |
66 | degree-days-Fahrenheitdegree-days-Fahrenheit | CIF-/IF-Module mapped; | |
67 | yearsyears | CIF-/IF-Module mapped; | |
68 | monthsmonths | CIF-/IF-Module mapped; | |
69 | weeksweeks | CIF-/IF-Module mapped; | |
70 | daysdays | CIF-/IF-Module mapped; | |
71 | hourshours | CIF-/IF-Module mapped; | |
72 | minutesminutes | CIF-/IF-Module mapped; | |
73 | s | secondsseconds | CIF-/IF-Module mapped; |
74 | meters-per-secondmeters-per-second | CIF-/IF-Module mapped; | |
75 | kilometers-per-hourkilometers-per-hour | CIF-/IF-Module mapped; | |
76 | feet-per-secondfeet-per-second | CIF-/IF-Module mapped; | |
77 | feet-per-minutefeet-per-minute | CIF-/IF-Module mapped; | |
78 | miles-per-hourmiles-per-hour | CIF-/IF-Module mapped; | |
79 | cubic-feetcubic-feet | CIF-/IF-Module mapped; | |
80 | cubic-meterscubic-meters | CIF-/IF-Module mapped; | |
81 | imperial-gallonsimperial-gallons | CIF-/IF-Module mapped; | |
82 | litersliters | CIF-/IF-Module mapped; | |
83 | us-gallonsus-gallons | CIF-/IF-Module mapped; | |
84 | cubic-feet-per-minutecubic-feet-per-minute | CIF-/IF-Module mapped; | |
85 | cubic-meters-per-secondcubic-meters-per-second | CIF-/IF-Module mapped; | |
86 | imperial-gallons-per-mimperial-gallons-per-m | CIF-/IF-Module mapped; | |
87 | liters-per-secondliters-per-second | CIF-/IF-Module mapped; | |
88 | liters-per-minuteliters-per-minute | CIF-/IF-Module mapped; | |
89 | us-gallons-per-minuteus-gallons-per-minute | CIF-/IF-Module mapped; | |
90 | degrees-angulardegrees-angular | CIF-/IF-Module mapped; | |
91 | degrees-Celsius-per-hourdegrees-Celsius-per-hour | CIF-/IF-Module mapped; | |
92 | degrees-Celsius-per-minutedegrees-Celsius-per-minute | CIF-/IF-Module mapped; | |
93 | degrees-Fahrenheit-per-hourdegrees-Fahrenheit-per-hour | CIF-/IF-Module mapped; | |
94 | degrees-Fahrenheit-per-minutedegrees-Fahrenheit-per-minute | CIF-/IF-Module mapped; | |
95 | no-unitsno-units | CIF-/IF-Module mapped; | |
96 | parts-per-millionparts-per-million | CIF-/IF-Module mapped; | |
97 | parts-per-billionparts-per-billion | CIF-/IF-Module mapped; | |
98 | percentpercent | CIF-/IF-Module mapped; | |
99 | percent-per-secondpercent-per-second | CIF-/IF-Module mapped; | |
100 | per-minuteper-minute | CIF-/IF-Module mapped; | |
101 | per-secondper-second | CIF-/IF-Module mapped; | |
102 | psi-per-degree-Fahrenheitpsi-per-degree-Fahrenheit | CIF-/IF-Module mapped; | |
103 | radiansradians | CIF-/IF-Module mapped; | |
104 | min-1 | revolutions-per-minuterevolutions-per-minute | CIF-/IF-Module mapped; |
105 | currency1currency1 | CIF-/IF-Module mapped; | |
106 | currency2currency2 | CIF-/IF-Module mapped; | |
107 | currency3currency3 | CIF-/IF-Module mapped; | |
108 | currency4currency4 | CIF-/IF-Module mapped; | |
109 | currency5currency5 | CIF-/IF-Module mapped; | |
110 | currency6currency6 | CIF-/IF-Module mapped; | |
111 | currency7currency7 | CIF-/IF-Module mapped; | |
112 | currency8currency8 | CIF-/IF-Module mapped; | |
113 | currency9currency9 | CIF-/IF-Module mapped; | |
114 | currency10currency10 | CIF-/IF-Module mapped; | |
115 | square-inchessquare-inches | CIF-/IF-Module mapped; | |
116 | square-centimeterssquare-centimeters | CIF-/IF-Module mapped; | |
117 | btus-per-poundbtus-per-pound | CIF-/IF-Module mapped; | |
118 | centimeterscentimeters | CIF-/IF-Module mapped; | |
119 | pounds-mass-per-secondpounds-mass-per-second | CIF-/IF-Module mapped; | |
120 | delta-degrees-Fahrenheitdelta-degrees-Fahrenheit | CIF-/IF-Module mapped; | |
121 | delta-degrees-Kelvindelta-degrees-Kelvin | CIF-/IF-Module mapped; | |
122 | kilohmskilohms | CIF-/IF-Module mapped; | |
123 | megohmsmegohms | CIF-/IF-Module mapped; | |
124 | millivoltsmillivolts | CIF-/IF-Module mapped; | |
125 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
126 | megajoulesmegajoules | CIF-/IF-Module mapped; | |
127 | joules-per-degree-Kelvinjoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
128 | joules-per-kilogram-degree-Kelvinjoules-per-kilogram-degree-Kelvin | CIF-/IF-Module mapped; | |
129 | kilohertzkilohertz | CIF-/IF-Module mapped; | |
130 | megahertzmegahertz | CIF-/IF-Module mapped; | |
131 | per-hourper-hour | CIF-/IF-Module mapped; | |
132 | milliwattsmilliwatts | CIF-/IF-Module mapped; | |
133 | hectopascalshectopascals | CIF-/IF-Module mapped; | |
134 | millibarsmillibars | CIF-/IF-Module mapped; | |
135 | m3/h | cubic-meters-per-hourcubic-meters-per-hour | CIF-/IF-Module mapped; |
136 | liters-per-hourliters-per-hour | CIF-/IF-Module mapped; | |
137 | kilowatt-hours-per-square-meterkilowatt-hours-per-square-meter | CIF-/IF-Module mapped; | |
138 | kilowatt-hours-per-square-footkilowatt-hours-per-square-foot | CIF-/IF-Module mapped; | |
139 | megajoules-per-square-metermegajoules-per-square-meter | CIF-/IF-Module mapped; | |
140 | megajoules-per-square-footmegajoules-per-square-foot | CIF-/IF-Module mapped; | |
141 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
142 | cubic-feet-per-secondcubic-feet-per-second | CIF-/IF-Module mapped; | |
143 | percent-obscuration-per-footpercent-obscuration-per-foot | CIF-/IF-Module mapped; | |
144 | percent-obscuration-per-meterpercent-obscuration-per-meter | CIF-/IF-Module mapped; | |
145 | milliohmsmilliohms | CIF-/IF-Module mapped; | |
146 | megawatt-hoursmegawatt-hours | CIF-/IF-Module mapped; | |
147 | kilo-btuskilo-btus | CIF-/IF-Module mapped; | |
148 | mega-btusmega-btus | CIF-/IF-Module mapped; | |
149 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
150 | megajoules-per-kilogrammegajoules-per-kilogram | CIF-/IF-Module mapped; | |
151 | kilojoules-per-degree-Kelvinkilojoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
152 | megajoules-per-degree-Kelvinmegajoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
153 | newtonnewton | CIF-/IF-Module mapped; | |
154 | grams-per-secondgrams-per-second | CIF-/IF-Module mapped; | |
155 | grams-per-minutegrams-per-minute | CIF-/IF-Module mapped; | |
156 | tons-per-hourtons-per-hour | CIF-/IF-Module mapped; | |
157 | kilo-btus-per-hourkilo-btus-per-hour | CIF-/IF-Module mapped; | |
158 | hundredths-secondshundredths-seconds | CIF-/IF-Module mapped; | |
159 | millisecondsmilliseconds | CIF-/IF-Module mapped; | |
160 | newton-metersnewton-meters | CIF-/IF-Module mapped; | |
161 | millimeters-per-secondmillimeters-per-second | CIF-/IF-Module mapped; | |
162 | millimeters-per-minutemillimeters-per-minute | CIF-/IF-Module mapped; | |
163 | meters-per-minutemeters-per-minute | CIF-/IF-Module mapped; | |
164 | meters-per-hourmeters-per-hour | CIF-/IF-Module mapped; | |
165 | cubic-meters-per-minutecubic-meters-per-minute | CIF-/IF-Module mapped; | |
166 | meters-per-second-per-secondmeters-per-second-per-second | CIF-/IF-Module mapped; | |
167 | amperes-per-meteramperes-per-meter | CIF-/IF-Module mapped; | |
168 | amperes-per-square-meteramperes-per-square-meter | CIF-/IF-Module mapped; | |
169 | ampere-square-metersampere-square-meters | CIF-/IF-Module mapped; | |
170 | faradsfarads | CIF-/IF-Module mapped; | |
171 | henryshenrys | CIF-/IF-Module mapped; | |
172 | ohm-metersohm-meters | CIF-/IF-Module mapped; | |
173 | siemenssiemens | CIF-/IF-Module mapped; | |
174 | siemens-per-metersiemens-per-meter | CIF-/IF-Module mapped; | |
175 | teslasteslas | CIF-/IF-Module mapped; | |
176 | volts-per-degree-Kelvinvolts-per-degree-Kelvin | CIF-/IF-Module mapped; | |
177 | volts-per-metervolts-per-meter | CIF-/IF-Module mapped; | |
178 | weberswebers | CIF-/IF-Module mapped; | |
179 | candelascandelas | CIF-/IF-Module mapped; | |
180 | candelas-per-square-metercandelas-per-square-meter | CIF-/IF-Module mapped; | |
181 | degrees-Kelvin-per-hourdegrees-Kelvin-per-hour | CIF-/IF-Module mapped; | |
182 | degrees-Kelvin-per-minutedegrees-Kelvin-per-minute | CIF-/IF-Module mapped; | |
183 | joule-secondsjoule-seconds | CIF-/IF-Module mapped; | |
184 | radians-per-secondradians-per-second | CIF-/IF-Module mapped; | |
185 | square-meters-per-Newtonsquare-meters-per-Newton | CIF-/IF-Module mapped; | |
186 | kilograms-per-cubic-meterkilograms-per-cubic-meter | CIF-/IF-Module mapped; | |
187 | newton-secondsnewton-seconds | CIF-/IF-Module mapped; | |
188 | newtons-per-meternewtons-per-meter | CIF-/IF-Module mapped; | |
189 | watts-per-meter-per-degree-Kelvinwatts-per-meter-per-degree-Kelvin | CIF-/IF-Module mapped; | |
190 | micro-siemensmicro-siemens | CIF-/IF-Module mapped; | |
191 | cubic-feet-per-hourcubic-feet-per-hour | CIF-/IF-Module mapped; | |
192 | us-gallons-per-hourus-gallons-per-hour | CIF-/IF-Module mapped; | |
193 | kilometerskilometers | CIF-/IF-Module mapped; | |
194 | micrometersmicrometers | CIF-/IF-Module mapped; | |
195 | gramsgrams | CIF-/IF-Module mapped; | |
196 | milligramsmilligrams | CIF-/IF-Module mapped; | |
197 | millilitersmilliliters | CIF-/IF-Module mapped; | |
198 | milliliters-per-secondmilliliters-per-second | CIF-/IF-Module mapped; | |
199 | decibelsdecibels | CIF-/IF-Module mapped; | |
200 | decibels-millivoltdecibels-millivolt | CIF-/IF-Module mapped; | |
201 | decibels-voltdecibels-volt | CIF-/IF-Module mapped; | |
202 | millisiemensmillisiemens | CIF-/IF-Module mapped; | |
203 | watt-hours-reactivewatt-hours-reactive | CIF-/IF-Module mapped; | |
204 | kilowatt-hours-reactivekilowatt-hours-reactive | CIF-/IF-Module mapped; | |
205 | megawatt-hours-reactivemegawatt-hours-reactive | CIF-/IF-Module mapped; | |
206 | millimeters-of-watermillimeters-of-water | CIF-/IF-Module mapped; | |
207 | per-milleper-mille | CIF-/IF-Module mapped; | |
208 | grams-per-gramgrams-per-gram | CIF-/IF-Module mapped; | |
209 | kilograms-per-kilogramkilograms-per-kilogram | CIF-/IF-Module mapped; | |
210 | grams-per-kilogramgrams-per-kilogram | CIF-/IF-Module mapped; | |
211 | milligrams-per-grammilligrams-per-gram | CIF-/IF-Module mapped; | |
212 | milligrams-per-kilogrammilligrams-per-kilogram | CIF-/IF-Module mapped; | |
213 | grams-per-millilitergrams-per-milliliter | CIF-/IF-Module mapped; | |
214 | grams-per-litergrams-per-liter | CIF-/IF-Module mapped; | |
215 | milligrams-per-litermilligrams-per-liter | CIF-/IF-Module mapped; | |
216 | micrograms-per-litermicrograms-per-liter | CIF-/IF-Module mapped; | |
217 | grams-per-cubic-metergrams-per-cubic-meter | CIF-/IF-Module mapped; | |
218 | milligrams-per-cubic-metermilligrams-per-cubic-meter | CIF-/IF-Module mapped; | |
219 | micrograms-per-cubic-metermicrograms-per-cubic-meter | CIF-/IF-Module mapped; | |
220 | nanograms-per-cubic-meternanograms-per-cubic-meter | CIF-/IF-Module mapped; | |
221 | grams-per-cubic-centimetergrams-per-cubic-centimeter | CIF-/IF-Module mapped; | |
222 | becquerelsbecquerels | CIF-/IF-Module mapped; | |
223 | kilobecquerelskilobecquerels | CIF-/IF-Module mapped; | |
224 | megabecquerelsmegabecquerels | CIF-/IF-Module mapped; | |
225 | graygray | CIF-/IF-Module mapped; | |
226 | milligraymilligray | CIF-/IF-Module mapped; | |
227 | micrograymicrogray | CIF-/IF-Module mapped; | |
228 | sievertssieverts | CIF-/IF-Module mapped; | |
229 | millisievertsmillisieverts | CIF-/IF-Module mapped; | |
230 | microsievertsmicrosieverts | CIF-/IF-Module mapped; | |
231 | microsieverts-per-hourmicrosieverts-per-hour | CIF-/IF-Module mapped; | |
232 | decibels-adecibels-a | CIF-/IF-Module mapped; | |
233 | nephelometric-turbidity-unitnephelometric-turbidity-unit | CIF-/IF-Module mapped; | |
234 | pHpH | CIF-/IF-Module mapped; | |
235 | grams-per-square-metergrams-per-square-meter | CIF-/IF-Module mapped; | |
236 | minutes-per-degree-kelvinminutes-per-degree-kelvin | CIF-/IF-Module mapped; | |
237 | meters-of-watermeters-of-water | CIF-/IF-Module mapped; | |
238 | timestamp-unixtimestamp-unix | CIF-/IF-Module mapped; | |
239 | m2 | square-meterssquare-meters | CIF-/IF-Module mapped; |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 210 |
scopeBereich | pump systemPumpensystem |
functionFunktion | active valueaktiver Wert |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.00…99.99), IF-Module Modbus Stratos (3.00…99.99), IF-Module Modbus (3.00…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | IF-Module | Signal source for setpoint: IF-ModuleSollwertquelle IF-Modul | Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …; |
2 | 0…10 V | Signal source for setpoint: IN2 mode 0…10 VSollwertquelle: IN2 Modus 0…10 V | CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …; |
3 | 2…10 V | Signal source for setpoint: IN2 mode 2…10 VSollwertquelle: IN2 Modus 2…10 V | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
4 | 0…20 mA | Signal source for setpoint: IN2 mode 0…20 mASollwertquelle: IN2 Modus 0…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
5 | 4…20 mA | Signal source for setpoint: IN2 mode 4…20 mASollwertquelle: IN2 Modus 4…20 mA | CIF-/IF-Module mapped; IL_E, …; MVIE, …; |
6 | Internal | Signal source for setpoint: internalSollwertquelle: Intern | Stratos MAXO; Stratos GIGA 2.0; |
7 | EXT 1 | Signal source for setpoint: EXT 1Sollwertquelle: EXT 1 | Stratos MAXO; Stratos GIGA 2.0; |
8 | EXT 2 | Signal source for setpoint: EXT 2Sollwertquelle: EXT 2 | Stratos MAXO; Stratos GIGA 2.0; |
9 | INVALID | Invalid valueUngültiger Wert | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Dieses Signal enthält die Sollwertquelle in der aktuellen Regelungsart. This is the base signal. This signal represents the source for the setpoint for the current control function.
Support reference: Wird unterstützt durch: Stratos MAXO; Stratos GIGA 2.0; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 211 |
scopeBereich | pump systemPumpensystem |
functionFunktion | value after parameter set selector (B)Wert nach Parametersatz-Selektor (B) |
data typeDatentyp | BYTE |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | norm | normal paremeter setParametersatz normal | CIF-/IF-Module internal; |
2 | aux | auxiliary parameter setParametersatz zusätzlich | CIF-/IF-Module internal; |
3 | preset | preset parameter set (startup/fallback)Parametersatz Preset (Voreinstellung / Fallback) | CIF-/IF-Module internal; |
5 | INVALID | value for parameter set invalidWert für Parametersatz ungültig | CIF-/IF-Module internal; |
Dieses Signal ist das Grundsignal. Dieses Signal beinhaltet die Information über den Parametersatz zur Steuerung des Geräts: Der Parametersatz umfasst mindestens Sollwert, Regelungsart, Pumpe ein/aus und Sollwertquelle.This is the base signal. This signal contains information about the parameter set for device control. The parameter set constist of at least the duty point, the control mode, the on/off command and the signal source for the duty point.
Support reference: Wird unterstützt durch: CIF-/IF-Module internal;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 222 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 224 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 226 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | REAL |
unitEinheit | - |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dieses Signal ist das Grundsignal. Dieses Signal liefert den 100 % Bezugswert für den Sollwert in der aktuellen Regelungsart.This is the base signal. This signal represent the 100 % reference value for the duty point in the current control function.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 228 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | UINT |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | square-feetsquare-feet | CIF-/IF-Module mapped; | |
2 | milliamperesmilliamperes | CIF-/IF-Module mapped; | |
3 | A | amperesamperes | CIF-/IF-Module mapped; |
4 | ohmsohms | CIF-/IF-Module mapped; | |
5 | V | voltsvolts | CIF-/IF-Module mapped; |
6 | kilovoltskilovolts | CIF-/IF-Module mapped; | |
7 | megavoltsmegavolts | CIF-/IF-Module mapped; | |
8 | volt-amperesvolt-amperes | CIF-/IF-Module mapped; | |
9 | kilovolt-ampereskilovolt-amperes | CIF-/IF-Module mapped; | |
10 | megavolt-amperesmegavolt-amperes | CIF-/IF-Module mapped; | |
11 | volt-amperes-reactivevolt-amperes-reactive | CIF-/IF-Module mapped; | |
12 | kilovolt-amperes-reactivekilovolt-amperes-reactive | CIF-/IF-Module mapped; | |
13 | megavolt-amperes-reactivemegavolt-amperes-reactive | CIF-/IF-Module mapped; | |
14 | degrees-phasedegrees-phase | CIF-/IF-Module mapped; | |
15 | power-factorpower-factor | CIF-/IF-Module mapped; | |
16 | joulesjoules | CIF-/IF-Module mapped; | |
17 | kilojouleskilojoules | CIF-/IF-Module mapped; | |
18 | watt-hourswatt-hours | CIF-/IF-Module mapped; | |
19 | kWh | kilowatt-hourskilowatt-hours | CIF-/IF-Module mapped; |
20 | btusbtus | CIF-/IF-Module mapped; | |
21 | thermstherms | CIF-/IF-Module mapped; | |
22 | ton-hourston-hours | CIF-/IF-Module mapped; | |
23 | joules-per-kilogram-dry-airjoules-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
24 | btus-per-pound-dry-airbtus-per-pound-dry-air | CIF-/IF-Module mapped; | |
25 | cycles-per-hourcycles-per-hour | CIF-/IF-Module mapped; | |
26 | cycles-per-minutecycles-per-minute | CIF-/IF-Module mapped; | |
27 | hertzhertz | CIF-/IF-Module mapped; | |
28 | grams-of-water-per-kilogram-dry-airgrams-of-water-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
29 | percent-relative-humiditypercent-relative-humidity | CIF-/IF-Module mapped; | |
30 | millimetersmillimeters | CIF-/IF-Module mapped; | |
31 | metersmeters | CIF-/IF-Module mapped; | |
32 | inchesinches | CIF-/IF-Module mapped; | |
33 | feetfeet | CIF-/IF-Module mapped; | |
34 | watts-per-square-footwatts-per-square-foot | CIF-/IF-Module mapped; | |
35 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
36 | lumenslumens | CIF-/IF-Module mapped; | |
37 | luxesluxes | CIF-/IF-Module mapped; | |
38 | foot-candlesfoot-candles | CIF-/IF-Module mapped; | |
39 | kilogramskilograms | CIF-/IF-Module mapped; | |
40 | pounds-masspounds-mass | CIF-/IF-Module mapped; | |
41 | tonstons | CIF-/IF-Module mapped; | |
42 | kilograms-per-secondkilograms-per-second | CIF-/IF-Module mapped; | |
43 | kilograms-per-minutekilograms-per-minute | CIF-/IF-Module mapped; | |
44 | kilograms-per-hourkilograms-per-hour | CIF-/IF-Module mapped; | |
45 | pounds-mass-per-minutepounds-mass-per-minute | CIF-/IF-Module mapped; | |
46 | pounds-mass-per-hourpounds-mass-per-hour | CIF-/IF-Module mapped; | |
47 | W | wattswatts | CIF-/IF-Module mapped; |
48 | kilowattskilowatts | CIF-/IF-Module mapped; | |
49 | megawattsmegawatts | CIF-/IF-Module mapped; | |
50 | btus-per-hourbtus-per-hour | CIF-/IF-Module mapped; | |
51 | horsepowerhorsepower | CIF-/IF-Module mapped; | |
52 | tons-refrigerationtons-refrigeration | CIF-/IF-Module mapped; | |
53 | pascalspascals | CIF-/IF-Module mapped; | |
54 | kilopascalskilopascals | CIF-/IF-Module mapped; | |
55 | bar | barsbars | CIF-/IF-Module mapped; |
56 | pounds-force-per-square-inchpounds-force-per-square-inch | CIF-/IF-Module mapped; | |
57 | centimeters-of-watercentimeters-of-water | CIF-/IF-Module mapped; | |
58 | inches-of-waterinches-of-water | CIF-/IF-Module mapped; | |
59 | millimeters-of-mercurymillimeters-of-mercury | CIF-/IF-Module mapped; | |
60 | centimeters-of-mercurycentimeters-of-mercury | CIF-/IF-Module mapped; | |
61 | inches-of-mercuryinches-of-mercury | CIF-/IF-Module mapped; | |
62 | Cel | degrees-Celsiusdegrees-Celsius | CIF-/IF-Module mapped; |
63 | K | degrees-Kelvindegrees-Kelvin | CIF-/IF-Module mapped; |
64 | degrees-Fahrenheitdegrees-Fahrenheit | CIF-/IF-Module mapped; | |
65 | degree-days-Celsiusdegree-days-Celsius | CIF-/IF-Module mapped; | |
66 | degree-days-Fahrenheitdegree-days-Fahrenheit | CIF-/IF-Module mapped; | |
67 | yearsyears | CIF-/IF-Module mapped; | |
68 | monthsmonths | CIF-/IF-Module mapped; | |
69 | weeksweeks | CIF-/IF-Module mapped; | |
70 | daysdays | CIF-/IF-Module mapped; | |
71 | hourshours | CIF-/IF-Module mapped; | |
72 | minutesminutes | CIF-/IF-Module mapped; | |
73 | s | secondsseconds | CIF-/IF-Module mapped; |
74 | meters-per-secondmeters-per-second | CIF-/IF-Module mapped; | |
75 | kilometers-per-hourkilometers-per-hour | CIF-/IF-Module mapped; | |
76 | feet-per-secondfeet-per-second | CIF-/IF-Module mapped; | |
77 | feet-per-minutefeet-per-minute | CIF-/IF-Module mapped; | |
78 | miles-per-hourmiles-per-hour | CIF-/IF-Module mapped; | |
79 | cubic-feetcubic-feet | CIF-/IF-Module mapped; | |
80 | cubic-meterscubic-meters | CIF-/IF-Module mapped; | |
81 | imperial-gallonsimperial-gallons | CIF-/IF-Module mapped; | |
82 | litersliters | CIF-/IF-Module mapped; | |
83 | us-gallonsus-gallons | CIF-/IF-Module mapped; | |
84 | cubic-feet-per-minutecubic-feet-per-minute | CIF-/IF-Module mapped; | |
85 | cubic-meters-per-secondcubic-meters-per-second | CIF-/IF-Module mapped; | |
86 | imperial-gallons-per-mimperial-gallons-per-m | CIF-/IF-Module mapped; | |
87 | liters-per-secondliters-per-second | CIF-/IF-Module mapped; | |
88 | liters-per-minuteliters-per-minute | CIF-/IF-Module mapped; | |
89 | us-gallons-per-minuteus-gallons-per-minute | CIF-/IF-Module mapped; | |
90 | degrees-angulardegrees-angular | CIF-/IF-Module mapped; | |
91 | degrees-Celsius-per-hourdegrees-Celsius-per-hour | CIF-/IF-Module mapped; | |
92 | degrees-Celsius-per-minutedegrees-Celsius-per-minute | CIF-/IF-Module mapped; | |
93 | degrees-Fahrenheit-per-hourdegrees-Fahrenheit-per-hour | CIF-/IF-Module mapped; | |
94 | degrees-Fahrenheit-per-minutedegrees-Fahrenheit-per-minute | CIF-/IF-Module mapped; | |
95 | no-unitsno-units | CIF-/IF-Module mapped; | |
96 | parts-per-millionparts-per-million | CIF-/IF-Module mapped; | |
97 | parts-per-billionparts-per-billion | CIF-/IF-Module mapped; | |
98 | percentpercent | CIF-/IF-Module mapped; | |
99 | percent-per-secondpercent-per-second | CIF-/IF-Module mapped; | |
100 | per-minuteper-minute | CIF-/IF-Module mapped; | |
101 | per-secondper-second | CIF-/IF-Module mapped; | |
102 | psi-per-degree-Fahrenheitpsi-per-degree-Fahrenheit | CIF-/IF-Module mapped; | |
103 | radiansradians | CIF-/IF-Module mapped; | |
104 | min-1 | revolutions-per-minuterevolutions-per-minute | CIF-/IF-Module mapped; |
105 | currency1currency1 | CIF-/IF-Module mapped; | |
106 | currency2currency2 | CIF-/IF-Module mapped; | |
107 | currency3currency3 | CIF-/IF-Module mapped; | |
108 | currency4currency4 | CIF-/IF-Module mapped; | |
109 | currency5currency5 | CIF-/IF-Module mapped; | |
110 | currency6currency6 | CIF-/IF-Module mapped; | |
111 | currency7currency7 | CIF-/IF-Module mapped; | |
112 | currency8currency8 | CIF-/IF-Module mapped; | |
113 | currency9currency9 | CIF-/IF-Module mapped; | |
114 | currency10currency10 | CIF-/IF-Module mapped; | |
115 | square-inchessquare-inches | CIF-/IF-Module mapped; | |
116 | square-centimeterssquare-centimeters | CIF-/IF-Module mapped; | |
117 | btus-per-poundbtus-per-pound | CIF-/IF-Module mapped; | |
118 | centimeterscentimeters | CIF-/IF-Module mapped; | |
119 | pounds-mass-per-secondpounds-mass-per-second | CIF-/IF-Module mapped; | |
120 | delta-degrees-Fahrenheitdelta-degrees-Fahrenheit | CIF-/IF-Module mapped; | |
121 | delta-degrees-Kelvindelta-degrees-Kelvin | CIF-/IF-Module mapped; | |
122 | kilohmskilohms | CIF-/IF-Module mapped; | |
123 | megohmsmegohms | CIF-/IF-Module mapped; | |
124 | millivoltsmillivolts | CIF-/IF-Module mapped; | |
125 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
126 | megajoulesmegajoules | CIF-/IF-Module mapped; | |
127 | joules-per-degree-Kelvinjoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
128 | joules-per-kilogram-degree-Kelvinjoules-per-kilogram-degree-Kelvin | CIF-/IF-Module mapped; | |
129 | kilohertzkilohertz | CIF-/IF-Module mapped; | |
130 | megahertzmegahertz | CIF-/IF-Module mapped; | |
131 | per-hourper-hour | CIF-/IF-Module mapped; | |
132 | milliwattsmilliwatts | CIF-/IF-Module mapped; | |
133 | hectopascalshectopascals | CIF-/IF-Module mapped; | |
134 | millibarsmillibars | CIF-/IF-Module mapped; | |
135 | m3/h | cubic-meters-per-hourcubic-meters-per-hour | CIF-/IF-Module mapped; |
136 | liters-per-hourliters-per-hour | CIF-/IF-Module mapped; | |
137 | kilowatt-hours-per-square-meterkilowatt-hours-per-square-meter | CIF-/IF-Module mapped; | |
138 | kilowatt-hours-per-square-footkilowatt-hours-per-square-foot | CIF-/IF-Module mapped; | |
139 | megajoules-per-square-metermegajoules-per-square-meter | CIF-/IF-Module mapped; | |
140 | megajoules-per-square-footmegajoules-per-square-foot | CIF-/IF-Module mapped; | |
141 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
142 | cubic-feet-per-secondcubic-feet-per-second | CIF-/IF-Module mapped; | |
143 | percent-obscuration-per-footpercent-obscuration-per-foot | CIF-/IF-Module mapped; | |
144 | percent-obscuration-per-meterpercent-obscuration-per-meter | CIF-/IF-Module mapped; | |
145 | milliohmsmilliohms | CIF-/IF-Module mapped; | |
146 | megawatt-hoursmegawatt-hours | CIF-/IF-Module mapped; | |
147 | kilo-btuskilo-btus | CIF-/IF-Module mapped; | |
148 | mega-btusmega-btus | CIF-/IF-Module mapped; | |
149 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
150 | megajoules-per-kilogrammegajoules-per-kilogram | CIF-/IF-Module mapped; | |
151 | kilojoules-per-degree-Kelvinkilojoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
152 | megajoules-per-degree-Kelvinmegajoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
153 | newtonnewton | CIF-/IF-Module mapped; | |
154 | grams-per-secondgrams-per-second | CIF-/IF-Module mapped; | |
155 | grams-per-minutegrams-per-minute | CIF-/IF-Module mapped; | |
156 | tons-per-hourtons-per-hour | CIF-/IF-Module mapped; | |
157 | kilo-btus-per-hourkilo-btus-per-hour | CIF-/IF-Module mapped; | |
158 | hundredths-secondshundredths-seconds | CIF-/IF-Module mapped; | |
159 | millisecondsmilliseconds | CIF-/IF-Module mapped; | |
160 | newton-metersnewton-meters | CIF-/IF-Module mapped; | |
161 | millimeters-per-secondmillimeters-per-second | CIF-/IF-Module mapped; | |
162 | millimeters-per-minutemillimeters-per-minute | CIF-/IF-Module mapped; | |
163 | meters-per-minutemeters-per-minute | CIF-/IF-Module mapped; | |
164 | meters-per-hourmeters-per-hour | CIF-/IF-Module mapped; | |
165 | cubic-meters-per-minutecubic-meters-per-minute | CIF-/IF-Module mapped; | |
166 | meters-per-second-per-secondmeters-per-second-per-second | CIF-/IF-Module mapped; | |
167 | amperes-per-meteramperes-per-meter | CIF-/IF-Module mapped; | |
168 | amperes-per-square-meteramperes-per-square-meter | CIF-/IF-Module mapped; | |
169 | ampere-square-metersampere-square-meters | CIF-/IF-Module mapped; | |
170 | faradsfarads | CIF-/IF-Module mapped; | |
171 | henryshenrys | CIF-/IF-Module mapped; | |
172 | ohm-metersohm-meters | CIF-/IF-Module mapped; | |
173 | siemenssiemens | CIF-/IF-Module mapped; | |
174 | siemens-per-metersiemens-per-meter | CIF-/IF-Module mapped; | |
175 | teslasteslas | CIF-/IF-Module mapped; | |
176 | volts-per-degree-Kelvinvolts-per-degree-Kelvin | CIF-/IF-Module mapped; | |
177 | volts-per-metervolts-per-meter | CIF-/IF-Module mapped; | |
178 | weberswebers | CIF-/IF-Module mapped; | |
179 | candelascandelas | CIF-/IF-Module mapped; | |
180 | candelas-per-square-metercandelas-per-square-meter | CIF-/IF-Module mapped; | |
181 | degrees-Kelvin-per-hourdegrees-Kelvin-per-hour | CIF-/IF-Module mapped; | |
182 | degrees-Kelvin-per-minutedegrees-Kelvin-per-minute | CIF-/IF-Module mapped; | |
183 | joule-secondsjoule-seconds | CIF-/IF-Module mapped; | |
184 | radians-per-secondradians-per-second | CIF-/IF-Module mapped; | |
185 | square-meters-per-Newtonsquare-meters-per-Newton | CIF-/IF-Module mapped; | |
186 | kilograms-per-cubic-meterkilograms-per-cubic-meter | CIF-/IF-Module mapped; | |
187 | newton-secondsnewton-seconds | CIF-/IF-Module mapped; | |
188 | newtons-per-meternewtons-per-meter | CIF-/IF-Module mapped; | |
189 | watts-per-meter-per-degree-Kelvinwatts-per-meter-per-degree-Kelvin | CIF-/IF-Module mapped; | |
190 | micro-siemensmicro-siemens | CIF-/IF-Module mapped; | |
191 | cubic-feet-per-hourcubic-feet-per-hour | CIF-/IF-Module mapped; | |
192 | us-gallons-per-hourus-gallons-per-hour | CIF-/IF-Module mapped; | |
193 | kilometerskilometers | CIF-/IF-Module mapped; | |
194 | micrometersmicrometers | CIF-/IF-Module mapped; | |
195 | gramsgrams | CIF-/IF-Module mapped; | |
196 | milligramsmilligrams | CIF-/IF-Module mapped; | |
197 | millilitersmilliliters | CIF-/IF-Module mapped; | |
198 | milliliters-per-secondmilliliters-per-second | CIF-/IF-Module mapped; | |
199 | decibelsdecibels | CIF-/IF-Module mapped; | |
200 | decibels-millivoltdecibels-millivolt | CIF-/IF-Module mapped; | |
201 | decibels-voltdecibels-volt | CIF-/IF-Module mapped; | |
202 | millisiemensmillisiemens | CIF-/IF-Module mapped; | |
203 | watt-hours-reactivewatt-hours-reactive | CIF-/IF-Module mapped; | |
204 | kilowatt-hours-reactivekilowatt-hours-reactive | CIF-/IF-Module mapped; | |
205 | megawatt-hours-reactivemegawatt-hours-reactive | CIF-/IF-Module mapped; | |
206 | millimeters-of-watermillimeters-of-water | CIF-/IF-Module mapped; | |
207 | per-milleper-mille | CIF-/IF-Module mapped; | |
208 | grams-per-gramgrams-per-gram | CIF-/IF-Module mapped; | |
209 | kilograms-per-kilogramkilograms-per-kilogram | CIF-/IF-Module mapped; | |
210 | grams-per-kilogramgrams-per-kilogram | CIF-/IF-Module mapped; | |
211 | milligrams-per-grammilligrams-per-gram | CIF-/IF-Module mapped; | |
212 | milligrams-per-kilogrammilligrams-per-kilogram | CIF-/IF-Module mapped; | |
213 | grams-per-millilitergrams-per-milliliter | CIF-/IF-Module mapped; | |
214 | grams-per-litergrams-per-liter | CIF-/IF-Module mapped; | |
215 | milligrams-per-litermilligrams-per-liter | CIF-/IF-Module mapped; | |
216 | micrograms-per-litermicrograms-per-liter | CIF-/IF-Module mapped; | |
217 | grams-per-cubic-metergrams-per-cubic-meter | CIF-/IF-Module mapped; | |
218 | milligrams-per-cubic-metermilligrams-per-cubic-meter | CIF-/IF-Module mapped; | |
219 | micrograms-per-cubic-metermicrograms-per-cubic-meter | CIF-/IF-Module mapped; | |
220 | nanograms-per-cubic-meternanograms-per-cubic-meter | CIF-/IF-Module mapped; | |
221 | grams-per-cubic-centimetergrams-per-cubic-centimeter | CIF-/IF-Module mapped; | |
222 | becquerelsbecquerels | CIF-/IF-Module mapped; | |
223 | kilobecquerelskilobecquerels | CIF-/IF-Module mapped; | |
224 | megabecquerelsmegabecquerels | CIF-/IF-Module mapped; | |
225 | graygray | CIF-/IF-Module mapped; | |
226 | milligraymilligray | CIF-/IF-Module mapped; | |
227 | micrograymicrogray | CIF-/IF-Module mapped; | |
228 | sievertssieverts | CIF-/IF-Module mapped; | |
229 | millisievertsmillisieverts | CIF-/IF-Module mapped; | |
230 | microsievertsmicrosieverts | CIF-/IF-Module mapped; | |
231 | microsieverts-per-hourmicrosieverts-per-hour | CIF-/IF-Module mapped; | |
232 | decibels-adecibels-a | CIF-/IF-Module mapped; | |
233 | nephelometric-turbidity-unitnephelometric-turbidity-unit | CIF-/IF-Module mapped; | |
234 | pHpH | CIF-/IF-Module mapped; | |
235 | grams-per-square-metergrams-per-square-meter | CIF-/IF-Module mapped; | |
236 | minutes-per-degree-kelvinminutes-per-degree-kelvin | CIF-/IF-Module mapped; | |
237 | meters-of-watermeters-of-water | CIF-/IF-Module mapped; | |
238 | timestamp-unixtimestamp-unix | CIF-/IF-Module mapped; | |
239 | m2 | square-meterssquare-meters | CIF-/IF-Module mapped; |
Dieses Signal ist das Grundsignal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This is the base signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 232 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies definiert einen alternativen Wert für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This defines an alternative value for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 234 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies definiert einen alternativen Wert für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This defines an alternative value for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 236 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | REAL |
unitEinheit | - |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies definiert einen alternativen Wert für das folgende Signal. Dieses Signal liefert den 100 % Bezugswert für den Sollwert in der aktuellen Regelungsart.This defines an alternative value for the following signal. This signal represent the 100 % reference value for the duty point in the current control function.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 238 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | UINT |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | square-feetsquare-feet | CIF-/IF-Module mapped; | |
2 | milliamperesmilliamperes | CIF-/IF-Module mapped; | |
3 | A | amperesamperes | CIF-/IF-Module mapped; |
4 | ohmsohms | CIF-/IF-Module mapped; | |
5 | V | voltsvolts | CIF-/IF-Module mapped; |
6 | kilovoltskilovolts | CIF-/IF-Module mapped; | |
7 | megavoltsmegavolts | CIF-/IF-Module mapped; | |
8 | volt-amperesvolt-amperes | CIF-/IF-Module mapped; | |
9 | kilovolt-ampereskilovolt-amperes | CIF-/IF-Module mapped; | |
10 | megavolt-amperesmegavolt-amperes | CIF-/IF-Module mapped; | |
11 | volt-amperes-reactivevolt-amperes-reactive | CIF-/IF-Module mapped; | |
12 | kilovolt-amperes-reactivekilovolt-amperes-reactive | CIF-/IF-Module mapped; | |
13 | megavolt-amperes-reactivemegavolt-amperes-reactive | CIF-/IF-Module mapped; | |
14 | degrees-phasedegrees-phase | CIF-/IF-Module mapped; | |
15 | power-factorpower-factor | CIF-/IF-Module mapped; | |
16 | joulesjoules | CIF-/IF-Module mapped; | |
17 | kilojouleskilojoules | CIF-/IF-Module mapped; | |
18 | watt-hourswatt-hours | CIF-/IF-Module mapped; | |
19 | kWh | kilowatt-hourskilowatt-hours | CIF-/IF-Module mapped; |
20 | btusbtus | CIF-/IF-Module mapped; | |
21 | thermstherms | CIF-/IF-Module mapped; | |
22 | ton-hourston-hours | CIF-/IF-Module mapped; | |
23 | joules-per-kilogram-dry-airjoules-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
24 | btus-per-pound-dry-airbtus-per-pound-dry-air | CIF-/IF-Module mapped; | |
25 | cycles-per-hourcycles-per-hour | CIF-/IF-Module mapped; | |
26 | cycles-per-minutecycles-per-minute | CIF-/IF-Module mapped; | |
27 | hertzhertz | CIF-/IF-Module mapped; | |
28 | grams-of-water-per-kilogram-dry-airgrams-of-water-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
29 | percent-relative-humiditypercent-relative-humidity | CIF-/IF-Module mapped; | |
30 | millimetersmillimeters | CIF-/IF-Module mapped; | |
31 | metersmeters | CIF-/IF-Module mapped; | |
32 | inchesinches | CIF-/IF-Module mapped; | |
33 | feetfeet | CIF-/IF-Module mapped; | |
34 | watts-per-square-footwatts-per-square-foot | CIF-/IF-Module mapped; | |
35 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
36 | lumenslumens | CIF-/IF-Module mapped; | |
37 | luxesluxes | CIF-/IF-Module mapped; | |
38 | foot-candlesfoot-candles | CIF-/IF-Module mapped; | |
39 | kilogramskilograms | CIF-/IF-Module mapped; | |
40 | pounds-masspounds-mass | CIF-/IF-Module mapped; | |
41 | tonstons | CIF-/IF-Module mapped; | |
42 | kilograms-per-secondkilograms-per-second | CIF-/IF-Module mapped; | |
43 | kilograms-per-minutekilograms-per-minute | CIF-/IF-Module mapped; | |
44 | kilograms-per-hourkilograms-per-hour | CIF-/IF-Module mapped; | |
45 | pounds-mass-per-minutepounds-mass-per-minute | CIF-/IF-Module mapped; | |
46 | pounds-mass-per-hourpounds-mass-per-hour | CIF-/IF-Module mapped; | |
47 | W | wattswatts | CIF-/IF-Module mapped; |
48 | kilowattskilowatts | CIF-/IF-Module mapped; | |
49 | megawattsmegawatts | CIF-/IF-Module mapped; | |
50 | btus-per-hourbtus-per-hour | CIF-/IF-Module mapped; | |
51 | horsepowerhorsepower | CIF-/IF-Module mapped; | |
52 | tons-refrigerationtons-refrigeration | CIF-/IF-Module mapped; | |
53 | pascalspascals | CIF-/IF-Module mapped; | |
54 | kilopascalskilopascals | CIF-/IF-Module mapped; | |
55 | bar | barsbars | CIF-/IF-Module mapped; |
56 | pounds-force-per-square-inchpounds-force-per-square-inch | CIF-/IF-Module mapped; | |
57 | centimeters-of-watercentimeters-of-water | CIF-/IF-Module mapped; | |
58 | inches-of-waterinches-of-water | CIF-/IF-Module mapped; | |
59 | millimeters-of-mercurymillimeters-of-mercury | CIF-/IF-Module mapped; | |
60 | centimeters-of-mercurycentimeters-of-mercury | CIF-/IF-Module mapped; | |
61 | inches-of-mercuryinches-of-mercury | CIF-/IF-Module mapped; | |
62 | Cel | degrees-Celsiusdegrees-Celsius | CIF-/IF-Module mapped; |
63 | K | degrees-Kelvindegrees-Kelvin | CIF-/IF-Module mapped; |
64 | degrees-Fahrenheitdegrees-Fahrenheit | CIF-/IF-Module mapped; | |
65 | degree-days-Celsiusdegree-days-Celsius | CIF-/IF-Module mapped; | |
66 | degree-days-Fahrenheitdegree-days-Fahrenheit | CIF-/IF-Module mapped; | |
67 | yearsyears | CIF-/IF-Module mapped; | |
68 | monthsmonths | CIF-/IF-Module mapped; | |
69 | weeksweeks | CIF-/IF-Module mapped; | |
70 | daysdays | CIF-/IF-Module mapped; | |
71 | hourshours | CIF-/IF-Module mapped; | |
72 | minutesminutes | CIF-/IF-Module mapped; | |
73 | s | secondsseconds | CIF-/IF-Module mapped; |
74 | meters-per-secondmeters-per-second | CIF-/IF-Module mapped; | |
75 | kilometers-per-hourkilometers-per-hour | CIF-/IF-Module mapped; | |
76 | feet-per-secondfeet-per-second | CIF-/IF-Module mapped; | |
77 | feet-per-minutefeet-per-minute | CIF-/IF-Module mapped; | |
78 | miles-per-hourmiles-per-hour | CIF-/IF-Module mapped; | |
79 | cubic-feetcubic-feet | CIF-/IF-Module mapped; | |
80 | cubic-meterscubic-meters | CIF-/IF-Module mapped; | |
81 | imperial-gallonsimperial-gallons | CIF-/IF-Module mapped; | |
82 | litersliters | CIF-/IF-Module mapped; | |
83 | us-gallonsus-gallons | CIF-/IF-Module mapped; | |
84 | cubic-feet-per-minutecubic-feet-per-minute | CIF-/IF-Module mapped; | |
85 | cubic-meters-per-secondcubic-meters-per-second | CIF-/IF-Module mapped; | |
86 | imperial-gallons-per-mimperial-gallons-per-m | CIF-/IF-Module mapped; | |
87 | liters-per-secondliters-per-second | CIF-/IF-Module mapped; | |
88 | liters-per-minuteliters-per-minute | CIF-/IF-Module mapped; | |
89 | us-gallons-per-minuteus-gallons-per-minute | CIF-/IF-Module mapped; | |
90 | degrees-angulardegrees-angular | CIF-/IF-Module mapped; | |
91 | degrees-Celsius-per-hourdegrees-Celsius-per-hour | CIF-/IF-Module mapped; | |
92 | degrees-Celsius-per-minutedegrees-Celsius-per-minute | CIF-/IF-Module mapped; | |
93 | degrees-Fahrenheit-per-hourdegrees-Fahrenheit-per-hour | CIF-/IF-Module mapped; | |
94 | degrees-Fahrenheit-per-minutedegrees-Fahrenheit-per-minute | CIF-/IF-Module mapped; | |
95 | no-unitsno-units | CIF-/IF-Module mapped; | |
96 | parts-per-millionparts-per-million | CIF-/IF-Module mapped; | |
97 | parts-per-billionparts-per-billion | CIF-/IF-Module mapped; | |
98 | percentpercent | CIF-/IF-Module mapped; | |
99 | percent-per-secondpercent-per-second | CIF-/IF-Module mapped; | |
100 | per-minuteper-minute | CIF-/IF-Module mapped; | |
101 | per-secondper-second | CIF-/IF-Module mapped; | |
102 | psi-per-degree-Fahrenheitpsi-per-degree-Fahrenheit | CIF-/IF-Module mapped; | |
103 | radiansradians | CIF-/IF-Module mapped; | |
104 | min-1 | revolutions-per-minuterevolutions-per-minute | CIF-/IF-Module mapped; |
105 | currency1currency1 | CIF-/IF-Module mapped; | |
106 | currency2currency2 | CIF-/IF-Module mapped; | |
107 | currency3currency3 | CIF-/IF-Module mapped; | |
108 | currency4currency4 | CIF-/IF-Module mapped; | |
109 | currency5currency5 | CIF-/IF-Module mapped; | |
110 | currency6currency6 | CIF-/IF-Module mapped; | |
111 | currency7currency7 | CIF-/IF-Module mapped; | |
112 | currency8currency8 | CIF-/IF-Module mapped; | |
113 | currency9currency9 | CIF-/IF-Module mapped; | |
114 | currency10currency10 | CIF-/IF-Module mapped; | |
115 | square-inchessquare-inches | CIF-/IF-Module mapped; | |
116 | square-centimeterssquare-centimeters | CIF-/IF-Module mapped; | |
117 | btus-per-poundbtus-per-pound | CIF-/IF-Module mapped; | |
118 | centimeterscentimeters | CIF-/IF-Module mapped; | |
119 | pounds-mass-per-secondpounds-mass-per-second | CIF-/IF-Module mapped; | |
120 | delta-degrees-Fahrenheitdelta-degrees-Fahrenheit | CIF-/IF-Module mapped; | |
121 | delta-degrees-Kelvindelta-degrees-Kelvin | CIF-/IF-Module mapped; | |
122 | kilohmskilohms | CIF-/IF-Module mapped; | |
123 | megohmsmegohms | CIF-/IF-Module mapped; | |
124 | millivoltsmillivolts | CIF-/IF-Module mapped; | |
125 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
126 | megajoulesmegajoules | CIF-/IF-Module mapped; | |
127 | joules-per-degree-Kelvinjoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
128 | joules-per-kilogram-degree-Kelvinjoules-per-kilogram-degree-Kelvin | CIF-/IF-Module mapped; | |
129 | kilohertzkilohertz | CIF-/IF-Module mapped; | |
130 | megahertzmegahertz | CIF-/IF-Module mapped; | |
131 | per-hourper-hour | CIF-/IF-Module mapped; | |
132 | milliwattsmilliwatts | CIF-/IF-Module mapped; | |
133 | hectopascalshectopascals | CIF-/IF-Module mapped; | |
134 | millibarsmillibars | CIF-/IF-Module mapped; | |
135 | m3/h | cubic-meters-per-hourcubic-meters-per-hour | CIF-/IF-Module mapped; |
136 | liters-per-hourliters-per-hour | CIF-/IF-Module mapped; | |
137 | kilowatt-hours-per-square-meterkilowatt-hours-per-square-meter | CIF-/IF-Module mapped; | |
138 | kilowatt-hours-per-square-footkilowatt-hours-per-square-foot | CIF-/IF-Module mapped; | |
139 | megajoules-per-square-metermegajoules-per-square-meter | CIF-/IF-Module mapped; | |
140 | megajoules-per-square-footmegajoules-per-square-foot | CIF-/IF-Module mapped; | |
141 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
142 | cubic-feet-per-secondcubic-feet-per-second | CIF-/IF-Module mapped; | |
143 | percent-obscuration-per-footpercent-obscuration-per-foot | CIF-/IF-Module mapped; | |
144 | percent-obscuration-per-meterpercent-obscuration-per-meter | CIF-/IF-Module mapped; | |
145 | milliohmsmilliohms | CIF-/IF-Module mapped; | |
146 | megawatt-hoursmegawatt-hours | CIF-/IF-Module mapped; | |
147 | kilo-btuskilo-btus | CIF-/IF-Module mapped; | |
148 | mega-btusmega-btus | CIF-/IF-Module mapped; | |
149 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
150 | megajoules-per-kilogrammegajoules-per-kilogram | CIF-/IF-Module mapped; | |
151 | kilojoules-per-degree-Kelvinkilojoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
152 | megajoules-per-degree-Kelvinmegajoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
153 | newtonnewton | CIF-/IF-Module mapped; | |
154 | grams-per-secondgrams-per-second | CIF-/IF-Module mapped; | |
155 | grams-per-minutegrams-per-minute | CIF-/IF-Module mapped; | |
156 | tons-per-hourtons-per-hour | CIF-/IF-Module mapped; | |
157 | kilo-btus-per-hourkilo-btus-per-hour | CIF-/IF-Module mapped; | |
158 | hundredths-secondshundredths-seconds | CIF-/IF-Module mapped; | |
159 | millisecondsmilliseconds | CIF-/IF-Module mapped; | |
160 | newton-metersnewton-meters | CIF-/IF-Module mapped; | |
161 | millimeters-per-secondmillimeters-per-second | CIF-/IF-Module mapped; | |
162 | millimeters-per-minutemillimeters-per-minute | CIF-/IF-Module mapped; | |
163 | meters-per-minutemeters-per-minute | CIF-/IF-Module mapped; | |
164 | meters-per-hourmeters-per-hour | CIF-/IF-Module mapped; | |
165 | cubic-meters-per-minutecubic-meters-per-minute | CIF-/IF-Module mapped; | |
166 | meters-per-second-per-secondmeters-per-second-per-second | CIF-/IF-Module mapped; | |
167 | amperes-per-meteramperes-per-meter | CIF-/IF-Module mapped; | |
168 | amperes-per-square-meteramperes-per-square-meter | CIF-/IF-Module mapped; | |
169 | ampere-square-metersampere-square-meters | CIF-/IF-Module mapped; | |
170 | faradsfarads | CIF-/IF-Module mapped; | |
171 | henryshenrys | CIF-/IF-Module mapped; | |
172 | ohm-metersohm-meters | CIF-/IF-Module mapped; | |
173 | siemenssiemens | CIF-/IF-Module mapped; | |
174 | siemens-per-metersiemens-per-meter | CIF-/IF-Module mapped; | |
175 | teslasteslas | CIF-/IF-Module mapped; | |
176 | volts-per-degree-Kelvinvolts-per-degree-Kelvin | CIF-/IF-Module mapped; | |
177 | volts-per-metervolts-per-meter | CIF-/IF-Module mapped; | |
178 | weberswebers | CIF-/IF-Module mapped; | |
179 | candelascandelas | CIF-/IF-Module mapped; | |
180 | candelas-per-square-metercandelas-per-square-meter | CIF-/IF-Module mapped; | |
181 | degrees-Kelvin-per-hourdegrees-Kelvin-per-hour | CIF-/IF-Module mapped; | |
182 | degrees-Kelvin-per-minutedegrees-Kelvin-per-minute | CIF-/IF-Module mapped; | |
183 | joule-secondsjoule-seconds | CIF-/IF-Module mapped; | |
184 | radians-per-secondradians-per-second | CIF-/IF-Module mapped; | |
185 | square-meters-per-Newtonsquare-meters-per-Newton | CIF-/IF-Module mapped; | |
186 | kilograms-per-cubic-meterkilograms-per-cubic-meter | CIF-/IF-Module mapped; | |
187 | newton-secondsnewton-seconds | CIF-/IF-Module mapped; | |
188 | newtons-per-meternewtons-per-meter | CIF-/IF-Module mapped; | |
189 | watts-per-meter-per-degree-Kelvinwatts-per-meter-per-degree-Kelvin | CIF-/IF-Module mapped; | |
190 | micro-siemensmicro-siemens | CIF-/IF-Module mapped; | |
191 | cubic-feet-per-hourcubic-feet-per-hour | CIF-/IF-Module mapped; | |
192 | us-gallons-per-hourus-gallons-per-hour | CIF-/IF-Module mapped; | |
193 | kilometerskilometers | CIF-/IF-Module mapped; | |
194 | micrometersmicrometers | CIF-/IF-Module mapped; | |
195 | gramsgrams | CIF-/IF-Module mapped; | |
196 | milligramsmilligrams | CIF-/IF-Module mapped; | |
197 | millilitersmilliliters | CIF-/IF-Module mapped; | |
198 | milliliters-per-secondmilliliters-per-second | CIF-/IF-Module mapped; | |
199 | decibelsdecibels | CIF-/IF-Module mapped; | |
200 | decibels-millivoltdecibels-millivolt | CIF-/IF-Module mapped; | |
201 | decibels-voltdecibels-volt | CIF-/IF-Module mapped; | |
202 | millisiemensmillisiemens | CIF-/IF-Module mapped; | |
203 | watt-hours-reactivewatt-hours-reactive | CIF-/IF-Module mapped; | |
204 | kilowatt-hours-reactivekilowatt-hours-reactive | CIF-/IF-Module mapped; | |
205 | megawatt-hours-reactivemegawatt-hours-reactive | CIF-/IF-Module mapped; | |
206 | millimeters-of-watermillimeters-of-water | CIF-/IF-Module mapped; | |
207 | per-milleper-mille | CIF-/IF-Module mapped; | |
208 | grams-per-gramgrams-per-gram | CIF-/IF-Module mapped; | |
209 | kilograms-per-kilogramkilograms-per-kilogram | CIF-/IF-Module mapped; | |
210 | grams-per-kilogramgrams-per-kilogram | CIF-/IF-Module mapped; | |
211 | milligrams-per-grammilligrams-per-gram | CIF-/IF-Module mapped; | |
212 | milligrams-per-kilogrammilligrams-per-kilogram | CIF-/IF-Module mapped; | |
213 | grams-per-millilitergrams-per-milliliter | CIF-/IF-Module mapped; | |
214 | grams-per-litergrams-per-liter | CIF-/IF-Module mapped; | |
215 | milligrams-per-litermilligrams-per-liter | CIF-/IF-Module mapped; | |
216 | micrograms-per-litermicrograms-per-liter | CIF-/IF-Module mapped; | |
217 | grams-per-cubic-metergrams-per-cubic-meter | CIF-/IF-Module mapped; | |
218 | milligrams-per-cubic-metermilligrams-per-cubic-meter | CIF-/IF-Module mapped; | |
219 | micrograms-per-cubic-metermicrograms-per-cubic-meter | CIF-/IF-Module mapped; | |
220 | nanograms-per-cubic-meternanograms-per-cubic-meter | CIF-/IF-Module mapped; | |
221 | grams-per-cubic-centimetergrams-per-cubic-centimeter | CIF-/IF-Module mapped; | |
222 | becquerelsbecquerels | CIF-/IF-Module mapped; | |
223 | kilobecquerelskilobecquerels | CIF-/IF-Module mapped; | |
224 | megabecquerelsmegabecquerels | CIF-/IF-Module mapped; | |
225 | graygray | CIF-/IF-Module mapped; | |
226 | milligraymilligray | CIF-/IF-Module mapped; | |
227 | micrograymicrogray | CIF-/IF-Module mapped; | |
228 | sievertssieverts | CIF-/IF-Module mapped; | |
229 | millisievertsmillisieverts | CIF-/IF-Module mapped; | |
230 | microsievertsmicrosieverts | CIF-/IF-Module mapped; | |
231 | microsieverts-per-hourmicrosieverts-per-hour | CIF-/IF-Module mapped; | |
232 | decibels-adecibels-a | CIF-/IF-Module mapped; | |
233 | nephelometric-turbidity-unitnephelometric-turbidity-unit | CIF-/IF-Module mapped; | |
234 | pHpH | CIF-/IF-Module mapped; | |
235 | grams-per-square-metergrams-per-square-meter | CIF-/IF-Module mapped; | |
236 | minutes-per-degree-kelvinminutes-per-degree-kelvin | CIF-/IF-Module mapped; | |
237 | meters-of-watermeters-of-water | CIF-/IF-Module mapped; | |
238 | timestamp-unixtimestamp-unix | CIF-/IF-Module mapped; | |
239 | m2 | square-meterssquare-meters | CIF-/IF-Module mapped; |
Dies definiert einen alternativen Wert für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This defines an alternative value for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 242 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies beinhaltet eine Voreinstellung für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This incorporates a preset or fallback function for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 244 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | INT |
unitEinheit | % |
scaleSkalierung | 0.5 |
range lowBereich min. | -32768 |
range highBereich max. | 32766 |
error valueFehlerwert | 32767 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies beinhaltet eine Voreinstellung für das folgende Signal. Es beinhaltet den relativen Arbeitspunkt für das Gerät. Der gültige Bereich ist nicht zwingend 0…100 %. Ein bestimmter Arbeitspunkt signalisiert nicht unbedingt den Ein/Aus Zustand des Gerätes. This incorporates a preset or fallback function for the following signal. It contains the relative duty point of the device. The valid range is not necessarily 0…100 %. a duty point of 0 % is not necessarily linked to the OFF state of the device.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped; Stratos; IL_E, …; MVIE, …;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 246 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | REAL |
unitEinheit | - |
scaleSkalierung | 1 |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
Dies beinhaltet eine Voreinstellung für das folgende Signal. Dieses Signal liefert den 100 % Bezugswert für den Sollwert in der aktuellen Regelungsart.This incorporates a preset or fallback function for the following signal. This signal represent the 100 % reference value for the duty point in the current control function.
Support reference: Wird unterstützt durch: CIF-/IF-Module mapped;
propertyEigenschaft | valueWert |
---|---|
addressAdresse | 248 |
scopeBereich | pump systemPumpensystem |
functionFunktion | readback input value (A)Rücklesewert Eingang (A) |
data typeDatentyp | UINT |
Module versionsModul-Versionen | CIF-Module Ethernet Multiprotocol (3.03…99.99), CIF-Module Modbus RTU (3.01…99.99) |
valueWert | Name | descriptionBeschreibung | supportunterstützt durch |
---|---|---|---|
1 | square-feetsquare-feet | CIF-/IF-Module mapped; | |
2 | milliamperesmilliamperes | CIF-/IF-Module mapped; | |
3 | A | amperesamperes | CIF-/IF-Module mapped; |
4 | ohmsohms | CIF-/IF-Module mapped; | |
5 | V | voltsvolts | CIF-/IF-Module mapped; |
6 | kilovoltskilovolts | CIF-/IF-Module mapped; | |
7 | megavoltsmegavolts | CIF-/IF-Module mapped; | |
8 | volt-amperesvolt-amperes | CIF-/IF-Module mapped; | |
9 | kilovolt-ampereskilovolt-amperes | CIF-/IF-Module mapped; | |
10 | megavolt-amperesmegavolt-amperes | CIF-/IF-Module mapped; | |
11 | volt-amperes-reactivevolt-amperes-reactive | CIF-/IF-Module mapped; | |
12 | kilovolt-amperes-reactivekilovolt-amperes-reactive | CIF-/IF-Module mapped; | |
13 | megavolt-amperes-reactivemegavolt-amperes-reactive | CIF-/IF-Module mapped; | |
14 | degrees-phasedegrees-phase | CIF-/IF-Module mapped; | |
15 | power-factorpower-factor | CIF-/IF-Module mapped; | |
16 | joulesjoules | CIF-/IF-Module mapped; | |
17 | kilojouleskilojoules | CIF-/IF-Module mapped; | |
18 | watt-hourswatt-hours | CIF-/IF-Module mapped; | |
19 | kWh | kilowatt-hourskilowatt-hours | CIF-/IF-Module mapped; |
20 | btusbtus | CIF-/IF-Module mapped; | |
21 | thermstherms | CIF-/IF-Module mapped; | |
22 | ton-hourston-hours | CIF-/IF-Module mapped; | |
23 | joules-per-kilogram-dry-airjoules-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
24 | btus-per-pound-dry-airbtus-per-pound-dry-air | CIF-/IF-Module mapped; | |
25 | cycles-per-hourcycles-per-hour | CIF-/IF-Module mapped; | |
26 | cycles-per-minutecycles-per-minute | CIF-/IF-Module mapped; | |
27 | hertzhertz | CIF-/IF-Module mapped; | |
28 | grams-of-water-per-kilogram-dry-airgrams-of-water-per-kilogram-dry-air | CIF-/IF-Module mapped; | |
29 | percent-relative-humiditypercent-relative-humidity | CIF-/IF-Module mapped; | |
30 | millimetersmillimeters | CIF-/IF-Module mapped; | |
31 | metersmeters | CIF-/IF-Module mapped; | |
32 | inchesinches | CIF-/IF-Module mapped; | |
33 | feetfeet | CIF-/IF-Module mapped; | |
34 | watts-per-square-footwatts-per-square-foot | CIF-/IF-Module mapped; | |
35 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
36 | lumenslumens | CIF-/IF-Module mapped; | |
37 | luxesluxes | CIF-/IF-Module mapped; | |
38 | foot-candlesfoot-candles | CIF-/IF-Module mapped; | |
39 | kilogramskilograms | CIF-/IF-Module mapped; | |
40 | pounds-masspounds-mass | CIF-/IF-Module mapped; | |
41 | tonstons | CIF-/IF-Module mapped; | |
42 | kilograms-per-secondkilograms-per-second | CIF-/IF-Module mapped; | |
43 | kilograms-per-minutekilograms-per-minute | CIF-/IF-Module mapped; | |
44 | kilograms-per-hourkilograms-per-hour | CIF-/IF-Module mapped; | |
45 | pounds-mass-per-minutepounds-mass-per-minute | CIF-/IF-Module mapped; | |
46 | pounds-mass-per-hourpounds-mass-per-hour | CIF-/IF-Module mapped; | |
47 | W | wattswatts | CIF-/IF-Module mapped; |
48 | kilowattskilowatts | CIF-/IF-Module mapped; | |
49 | megawattsmegawatts | CIF-/IF-Module mapped; | |
50 | btus-per-hourbtus-per-hour | CIF-/IF-Module mapped; | |
51 | horsepowerhorsepower | CIF-/IF-Module mapped; | |
52 | tons-refrigerationtons-refrigeration | CIF-/IF-Module mapped; | |
53 | pascalspascals | CIF-/IF-Module mapped; | |
54 | kilopascalskilopascals | CIF-/IF-Module mapped; | |
55 | bar | barsbars | CIF-/IF-Module mapped; |
56 | pounds-force-per-square-inchpounds-force-per-square-inch | CIF-/IF-Module mapped; | |
57 | centimeters-of-watercentimeters-of-water | CIF-/IF-Module mapped; | |
58 | inches-of-waterinches-of-water | CIF-/IF-Module mapped; | |
59 | millimeters-of-mercurymillimeters-of-mercury | CIF-/IF-Module mapped; | |
60 | centimeters-of-mercurycentimeters-of-mercury | CIF-/IF-Module mapped; | |
61 | inches-of-mercuryinches-of-mercury | CIF-/IF-Module mapped; | |
62 | Cel | degrees-Celsiusdegrees-Celsius | CIF-/IF-Module mapped; |
63 | K | degrees-Kelvindegrees-Kelvin | CIF-/IF-Module mapped; |
64 | degrees-Fahrenheitdegrees-Fahrenheit | CIF-/IF-Module mapped; | |
65 | degree-days-Celsiusdegree-days-Celsius | CIF-/IF-Module mapped; | |
66 | degree-days-Fahrenheitdegree-days-Fahrenheit | CIF-/IF-Module mapped; | |
67 | yearsyears | CIF-/IF-Module mapped; | |
68 | monthsmonths | CIF-/IF-Module mapped; | |
69 | weeksweeks | CIF-/IF-Module mapped; | |
70 | daysdays | CIF-/IF-Module mapped; | |
71 | hourshours | CIF-/IF-Module mapped; | |
72 | minutesminutes | CIF-/IF-Module mapped; | |
73 | s | secondsseconds | CIF-/IF-Module mapped; |
74 | meters-per-secondmeters-per-second | CIF-/IF-Module mapped; | |
75 | kilometers-per-hourkilometers-per-hour | CIF-/IF-Module mapped; | |
76 | feet-per-secondfeet-per-second | CIF-/IF-Module mapped; | |
77 | feet-per-minutefeet-per-minute | CIF-/IF-Module mapped; | |
78 | miles-per-hourmiles-per-hour | CIF-/IF-Module mapped; | |
79 | cubic-feetcubic-feet | CIF-/IF-Module mapped; | |
80 | cubic-meterscubic-meters | CIF-/IF-Module mapped; | |
81 | imperial-gallonsimperial-gallons | CIF-/IF-Module mapped; | |
82 | litersliters | CIF-/IF-Module mapped; | |
83 | us-gallonsus-gallons | CIF-/IF-Module mapped; | |
84 | cubic-feet-per-minutecubic-feet-per-minute | CIF-/IF-Module mapped; | |
85 | cubic-meters-per-secondcubic-meters-per-second | CIF-/IF-Module mapped; | |
86 | imperial-gallons-per-mimperial-gallons-per-m | CIF-/IF-Module mapped; | |
87 | liters-per-secondliters-per-second | CIF-/IF-Module mapped; | |
88 | liters-per-minuteliters-per-minute | CIF-/IF-Module mapped; | |
89 | us-gallons-per-minuteus-gallons-per-minute | CIF-/IF-Module mapped; | |
90 | degrees-angulardegrees-angular | CIF-/IF-Module mapped; | |
91 | degrees-Celsius-per-hourdegrees-Celsius-per-hour | CIF-/IF-Module mapped; | |
92 | degrees-Celsius-per-minutedegrees-Celsius-per-minute | CIF-/IF-Module mapped; | |
93 | degrees-Fahrenheit-per-hourdegrees-Fahrenheit-per-hour | CIF-/IF-Module mapped; | |
94 | degrees-Fahrenheit-per-minutedegrees-Fahrenheit-per-minute | CIF-/IF-Module mapped; | |
95 | no-unitsno-units | CIF-/IF-Module mapped; | |
96 | parts-per-millionparts-per-million | CIF-/IF-Module mapped; | |
97 | parts-per-billionparts-per-billion | CIF-/IF-Module mapped; | |
98 | percentpercent | CIF-/IF-Module mapped; | |
99 | percent-per-secondpercent-per-second | CIF-/IF-Module mapped; | |
100 | per-minuteper-minute | CIF-/IF-Module mapped; | |
101 | per-secondper-second | CIF-/IF-Module mapped; | |
102 | psi-per-degree-Fahrenheitpsi-per-degree-Fahrenheit | CIF-/IF-Module mapped; | |
103 | radiansradians | CIF-/IF-Module mapped; | |
104 | min-1 | revolutions-per-minuterevolutions-per-minute | CIF-/IF-Module mapped; |
105 | currency1currency1 | CIF-/IF-Module mapped; | |
106 | currency2currency2 | CIF-/IF-Module mapped; | |
107 | currency3currency3 | CIF-/IF-Module mapped; | |
108 | currency4currency4 | CIF-/IF-Module mapped; | |
109 | currency5currency5 | CIF-/IF-Module mapped; | |
110 | currency6currency6 | CIF-/IF-Module mapped; | |
111 | currency7currency7 | CIF-/IF-Module mapped; | |
112 | currency8currency8 | CIF-/IF-Module mapped; | |
113 | currency9currency9 | CIF-/IF-Module mapped; | |
114 | currency10currency10 | CIF-/IF-Module mapped; | |
115 | square-inchessquare-inches | CIF-/IF-Module mapped; | |
116 | square-centimeterssquare-centimeters | CIF-/IF-Module mapped; | |
117 | btus-per-poundbtus-per-pound | CIF-/IF-Module mapped; | |
118 | centimeterscentimeters | CIF-/IF-Module mapped; | |
119 | pounds-mass-per-secondpounds-mass-per-second | CIF-/IF-Module mapped; | |
120 | delta-degrees-Fahrenheitdelta-degrees-Fahrenheit | CIF-/IF-Module mapped; | |
121 | delta-degrees-Kelvindelta-degrees-Kelvin | CIF-/IF-Module mapped; | |
122 | kilohmskilohms | CIF-/IF-Module mapped; | |
123 | megohmsmegohms | CIF-/IF-Module mapped; | |
124 | millivoltsmillivolts | CIF-/IF-Module mapped; | |
125 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
126 | megajoulesmegajoules | CIF-/IF-Module mapped; | |
127 | joules-per-degree-Kelvinjoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
128 | joules-per-kilogram-degree-Kelvinjoules-per-kilogram-degree-Kelvin | CIF-/IF-Module mapped; | |
129 | kilohertzkilohertz | CIF-/IF-Module mapped; | |
130 | megahertzmegahertz | CIF-/IF-Module mapped; | |
131 | per-hourper-hour | CIF-/IF-Module mapped; | |
132 | milliwattsmilliwatts | CIF-/IF-Module mapped; | |
133 | hectopascalshectopascals | CIF-/IF-Module mapped; | |
134 | millibarsmillibars | CIF-/IF-Module mapped; | |
135 | m3/h | cubic-meters-per-hourcubic-meters-per-hour | CIF-/IF-Module mapped; |
136 | liters-per-hourliters-per-hour | CIF-/IF-Module mapped; | |
137 | kilowatt-hours-per-square-meterkilowatt-hours-per-square-meter | CIF-/IF-Module mapped; | |
138 | kilowatt-hours-per-square-footkilowatt-hours-per-square-foot | CIF-/IF-Module mapped; | |
139 | megajoules-per-square-metermegajoules-per-square-meter | CIF-/IF-Module mapped; | |
140 | megajoules-per-square-footmegajoules-per-square-foot | CIF-/IF-Module mapped; | |
141 | watts-per-square-meterwatts-per-square-meter | CIF-/IF-Module mapped; | |
142 | cubic-feet-per-secondcubic-feet-per-second | CIF-/IF-Module mapped; | |
143 | percent-obscuration-per-footpercent-obscuration-per-foot | CIF-/IF-Module mapped; | |
144 | percent-obscuration-per-meterpercent-obscuration-per-meter | CIF-/IF-Module mapped; | |
145 | milliohmsmilliohms | CIF-/IF-Module mapped; | |
146 | megawatt-hoursmegawatt-hours | CIF-/IF-Module mapped; | |
147 | kilo-btuskilo-btus | CIF-/IF-Module mapped; | |
148 | mega-btusmega-btus | CIF-/IF-Module mapped; | |
149 | kilojoules-per-kilogramkilojoules-per-kilogram | CIF-/IF-Module mapped; | |
150 | megajoules-per-kilogrammegajoules-per-kilogram | CIF-/IF-Module mapped; | |
151 | kilojoules-per-degree-Kelvinkilojoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
152 | megajoules-per-degree-Kelvinmegajoules-per-degree-Kelvin | CIF-/IF-Module mapped; | |
153 | newtonnewton | CIF-/IF-Module mapped; | |
154 | grams-per-secondgrams-per-second | CIF-/IF-Module mapped; | |
155 | grams-per-minutegrams-per-minute | CIF-/IF-Module mapped; | |
156 | tons-per-hourtons-per-hour | CIF-/IF-Module mapped; | |
157 | kilo-btus-per-hourkilo-btus-per-hour | CIF-/IF-Module mapped; | |
158 | hundredths-secondshundredths-seconds | CIF-/IF-Module mapped; | |
159 | millisecondsmilliseconds | CIF-/IF-Module mapped; | |
160 | newton-metersnewton-meters | CIF-/IF-Module mapped; | |
161 | millimeters-per-secondmillimeters-per-second | CIF-/IF-Module mapped; | |
162 | millimeters-per-minutemillimeters-per-minute | CIF-/IF-Module mapped; | |
163 | meters-per-minutemeters-per-minute | CIF-/IF-Module mapped; | |
164 | meters-per-hourmeters-per-hour | CIF-/IF-Module mapped; | |
165 | cubic-meters-per-minutecubic-meters-per-minute | CIF-/IF-Module mapped; | |
166 | meters-per-second-per-secondmeters-per-second-per-second | CIF-/IF-Module mapped; | |
167 | amperes-per-meteramperes-per-meter | CIF-/IF-Module mapped; | |
168 | amperes-per-square-meteramperes-per-square-meter | CIF-/IF-Module mapped; | |
169 | ampere-square-metersampere-square-meters | CIF-/IF-Module mapped; | |
170 | faradsfarads | CIF-/IF-Module mapped; | |
171 | henryshenrys | CIF-/IF-Module mapped; | |
172 | ohm-metersohm-meters | CIF-/IF-Module mapped; | |
173 | siemenssiemens | CIF-/IF-Module mapped; | |
174 | siemens-per-metersiemens-per-meter | CIF-/IF-Module mapped; | |
175 | teslasteslas | CIF-/IF-Module mapped; | |
176 | volts-per-degree-Kelvinvolts-per-degree-Kelvin | CIF-/IF-Module mapped; | |
177 | volts-per-metervolts-per-meter | CIF-/IF-Module mapped; | |
178 | weberswebers | CIF-/IF-Module mapped; | |
179 | candelascandelas | CIF-/IF-Module mapped; | |
180 | candelas-per-square-metercandelas-per-square-meter | CIF-/IF-Module mapped; | |
181 | degrees-Kelvin-per-hourdegrees-Kelvin-per-hour | CIF-/IF-Module mapped; | |
182 | degrees-Kelvin-per-minutedegrees-Kelvin-per-minute | CIF-/IF-Module mapped; | |
183 | joule-secondsjoule-seconds | CIF-/IF-Module mapped; | |
184 | radians-per-secondradians-per-second | CIF-/IF-Module mapped; | |
185 | square-meters-per-Newtonsquare-meters-per-Newton | CIF-/IF-Module mapped; | |
186 | kilograms-per-cubic-meterkilograms-per-cubic-meter | CIF-/IF-Module mapped; | |
187 | newton-secondsnewton-seconds | CIF-/IF-Module mapped; | |
188 | newtons-per-meternewtons-per-meter | CIF-/IF-Module mapped; | |
189 | watts-per-meter-per-degree-Kelvinwatts-per-meter-per-degree-Kelvin | CIF-/IF-Module mapped; | |
190 | micro-siemensmicro-siemens | CIF-/IF-Module mapped; | |
191 | cubic-feet-per-hourcubic-feet-per-hour | CIF-/IF-Module mapped; | |
192 | us-gallons-per-hourus-gallons-per-hour | CIF-/IF-Module mapped; | |
193 | kilometerskilometers | CIF-/IF-Module mapped; | |
194 | micrometersmicrometers | CIF-/IF-Module mapped; | |
195 | gramsgrams | CIF-/IF-Module mapped; | |
196 | milligramsmilligrams | CIF-/IF-Module mapped; | |
197 | millilitersmilliliters | CIF-/IF-Module mapped; | |
198 | milliliters-per-secondmilliliters-per-second | CIF-/IF-Module mapped; | |
199 | decibelsdecibels | CIF-/IF-Module mapped; | |
200 | decibels-millivoltdecibels-millivolt | CIF-/IF-Module mapped; | |
201 | decibels-voltdecibels-volt | CIF-/IF-Module mapped; | |
202 | millisiemensmillisiemens | CIF-/IF-Module mapped; | |
203 | watt-hours-reactivewatt-hours-reactive | CIF-/IF-Module mapped; | |
204 | kilowatt-hours-reactivekilowatt-hours-reactive | CIF-/IF-Module mapped; | |
205 | megawatt-hours-reactivemegawatt-hours-reactive | CIF-/IF-Module mapped; | |
206 | millimeters-of-watermillimeters-of-water | CIF-/IF-Module mapped; | |
207 | per-milleper-mille | CIF-/IF-Module mapped; | |
208 | grams-per-gramgrams-per-gram | CIF-/IF-Module mapped; | |
209 | kilograms-per-kilogramkilograms-per-kilogram | CIF-/IF-Module mapped; | |
210 | grams-per-kilogramgrams-per-kilogram | CIF-/IF-Module mapped; | |
211 | milligrams-per-grammilligrams-per-gram | CIF-/IF-Module mapped; | |
212 | milligrams-per-kilogrammilligrams-per-kilogram | CIF-/IF-Module mapped; | |
213 | grams-per-millilitergrams-per-milliliter | CIF-/IF-Module mapped; | |
214 | grams-per-litergrams-per-liter | CIF-/IF-Module mapped; | |
215 | milligrams-per-litermilligrams-per-liter | CIF-/IF-Module mapped; | |
216 | micrograms-per-litermicrograms-per-liter | CIF-/IF-Module mapped; | |
217 | grams-per-cubic-metergrams-per-cubic-meter | CIF-/IF-Module mapped; | |
218 | milligrams-per-cubic-metermilligrams-per-cubic-meter | CIF-/IF-Module mapped; | |
219 | micrograms-per-cubic-metermicrograms-per-cubic-meter< |